drivers/input/touchscreen/Makefile

#
# Makefile for the mouse drivers.
#

# Each configuration option enables a list of files.

obj-$(CONFIG_TOUCHSCREEN_ADS7846)	+= ads7846.o
obj-$(CONFIG_TOUCHSCREEN_BITSY)	+= h3600_ts_input.o
obj-$(CONFIG_TOUCHSCREEN_CORGI)	+= corgi_ts.o
obj-$(CONFIG_TOUCHSCREEN_GUNZE)	+= gunze.o
obj-$(CONFIG_TOUCHSCREEN_ELO)	+= elo.o
obj-$(CONFIG_TOUCHSCREEN_MTOUCH) += mtouch.o
obj-$(CONFIG_TOUCHSCREEN_MK712)	+= mk712.o
obj-$(CONFIG_TOUCHSCREEN_HP600)	+= hp680_ts_input.o
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 15:20:36 -07:00			`#`
			`# Makefile for the mouse drivers.`
			`#`

			`# Each configuration option enables a list of files.`

[PATCH] spi: ads7846 driver This is a driver for the ADS7846 touchscreen sensor, derived from the corgi_ts and omap_ts drivers. Key differences from those two: - Uses the new SPI framework (minimalist version) - <linux/spi/ads7846.h> abstracts board-specific touchscreen info - Sysfs attributes for the temperature and voltage sensors - Uses fewer ARM-specific IRQ primitives The temperature and voltage sensors show up in sysfs like this: $ pwd /sys/devices/platform/omap-uwire/spi2.0 $ ls bus@ input:event0@ power/ temp1 vbatt driver@ modalias temp0 vaux $ cat modalias ads7846 $ cat temp0 991 $ cat temp1 1177 $ So far only basic testing has been done. There's a fair amount of hardware that uses this sensor, and which also runs Linux, which should eventually be able to use this driver. One portability note may be of special interest. It turns out that not all SPI controllers are happy issuing requests that do things like "write 8 bit command, read 12 bit response". Most of them seem happy to handle various word sizes, so the issue isn't "12 bit response" but rather "different rx and tx write sizes", despite that being a common MicroWire convention. So this version of the driver no longer reads 12 bit native-endian words; it reads 16-bit big-endian responses, then byteswaps them and shifts the results to discard the noise. Signed-off-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2006-01-08 13:34:21 -08:00			`obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 15:20:36 -07:00			`obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o`
			`obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o`
			`obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o`
			`obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o`
			`obj-$(CONFIG_TOUCHSCREEN_MTOUCH) += mtouch.o`
			`obj-$(CONFIG_TOUCHSCREEN_MK712) += mk712.o`
			`obj-$(CONFIG_TOUCHSCREEN_HP600) += hp680_ts_input.o`