Add PCI recovery functions to the driver. The initial PCI state is
also saved so the MSI state can be restored during PCI recovery.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added registers, memories, loopback, nvram, interrupt and link tests to
the self-test
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 TSO
Re-factor the Tx code with smaller functions to increase readability.
Add linearization code in case packet is too fragmented for the
microcode to handle.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TPA stands for Transparent Packet Aggregation. When enabled, the FW
aggregate in-order TCP packets according to the 4-tuple match and sends
1 big packet to the driver. This packet is stored on an SGL in which
each SGE is 1 page. The FW also implements a timeout algorithm and it
honors all TCP flag, including the push flag as a trigger to halt
aggregation.
After receiving Ben Hutchings comments, we also added ethtool support,
so now, thanks to Ben's patch, when forwarding is enabled, our
aggregation is turned off using the LRO flags.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions with link up/down and driver up/down - the
statistics handling was re-written in a form of state machine.
Also supporting statistics for 57711
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supporting the 57711 and 57711E - refers to in the code as E1H. The
57710 is referred to as E1.
To support the new members in the family, the bnx2x structure was
divided to 3 parts: common, port and function. These changes caused some
rearrangement in the bnx2x.h file.
A set of accessories macros were added to make access to the bnx2x
structure more readable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new Microcode BLOB - broken into a separate patch to make it small
enough for the mailing list
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new Microcode BLOB - broken into a separate patch to make it small
enough for the mailing list
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new Microcode BLOB - broken into a separate patch to make it small
enough for the mailing list
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the old Microcode from the BLOB - broken into a separate
patch to make it small enough for the mailing list
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new initialization code supports the 57711 HW. It also supports
the emulation and FPGA for the 57711 and 57710 initializations values
(very small amount of code which is very helpful in the lab - less
than 30 lines).
The initialization is done via DMAE after the DMAE block is ready -
before it is ready, some of the initialization is done via PCI
configuration transactions (referred to as indirect write). A mutex
to protect the DMAE from being overlapped was added. There are few
new registers which needs to be initialized by SW - the full comment
for those registers is added to the register file. A place holder for
the 57711 (referred to as E1H) microcode was added- the microcode
itself is too big and it is split over the following 4 patches
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New Link code:
Moving all the link related code (including the calculations, the
initialization of the MAC and PHY and the external PHY's code) into
a separated file. The changes from the code that used to be part of
bnx2x.c (now called bnx2x_main.c) are:
- Using separate structures for link inputs and link outputs to clearly
identify what was configured and what is the outcome
- Adding code to read external PHY FW version and print it as part of
ethtool -i
- Adding code to upgrade external PHY FW from ethtool -E with special
magic number - Changing the link down indication to ERR level
- Adding a lock on all PHY access to prevent an interrupt and
setting changes to overlap
- Adding support for emulation and FPGA (small chunk of code that really
helps in the lab) - Adding support for 1G on BCM8706 PHY
- Adding clear debug print incase of fan failure (the PHY type is now
"failure")
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is int the new bnx2x_link files (C and H). The files are
still not used in this patch, only in the next one so the patch will
be small enough for the mailing list.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilong Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the rename of bnx2x.c to bnx2x_main.c.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is based on x86/master branch of git-x86 tree, and has been tested
on x86_64 platform.
ChangeLog:
v2:
- Enclosing proc file system related code into CONFIG_PROVE_LOCKING.
- Fix nr_chain_hlocks update code.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: nfs_updatepage(): don't mark page as dirty if an error occurred
NFS: Fix filehandle size comparisons in the mount code
NFS: Reduce the NFS mount code stack usage.
Fix a sign issue in xdr_decode_fhstatus3()
Fix incorrect comparison in nfs_validate_mount_data()
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hidehiro Kawai noticed that sched_setscheduler() can fail in
stop_machine: it calls sched_setscheduler() from insmod, which can
have CAP_SYS_MODULE without CAP_SYS_NICE.
Two cases could have failed, so are changed to sched_setscheduler_nocheck:
kernel/softirq.c:cpu_callback()
- CPU hotplug callback
kernel/stop_machine.c:__stop_machine_run()
- Called from various places, including modprobe()
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Cc: sugita <yumiko.sugita.yf@hitachi.com>
Cc: Satoshi OSHIMA <satoshi.oshima.fk@hitachi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On the x86 platform we can use the value of tsc_khz computed during tsc
calibration to calculate the loops_per_jiffy value. Its very important
to keep the error in lpj values to minimum as any error in that may
result in kernel panic in check_timer. In virtualization environment, On
a highly overloaded host the guest delay calibration may sometimes
result in errors beyond the ~50% that timer_irq_works can handle,
resulting in the guest panicking.
Does some formating changes to lpj_setup code to now have a single
printk to print the bogomips value.
We do this only for the boot processor because the AP's can have
different base frequencies or the BIOS might boot a AP at a different
frequency.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Daniel Hecht <dhecht@vmware.com>
Cc: Tim Mann <mann@vmware.com>
Cc: Zach Amsden <zach@vmware.com>
Cc: Sahil Rihan <srihan@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Avoid modifying the mcount call-site if there is a kprobe installed on it.
These records are not marked as failed however. This allowed the filter
rules on them to remain up-to-date. Whenever the kprobe on the corresponding
record is removed, the record gets updated as normal.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Let records identified as being kprobe'd be marked as "frozen". The trouble
with records which have a kprobe installed on their mcount call-site is
that they don't get updated. So if such a function which is currently being
traced gets its tracing disabled due to a new filter rule (or because it
was added to the notrace list) then it won't be updated and continue being
traced. This patch allows scanning of all frozen records during tracing to
check if they should be traced.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Record the address of the mcount call-site. Currently all archs except sparc64
record the address of the instruction following the mcount call-site. Some
general cleanups are entailed. Storing mcount addresses in rec->ip enables
looking them up in the kprobe hash table later on to check if they're kprobe'd.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: davem@davemloft.net
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: refactor wait_for_completion_timeout()
sched: fix wait_for_completion_timeout() spurious failure under heavy load
sched: rt: dont stop the period timer when there are tasks wanting to run
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: don't drop NX bit
xen: mask unwanted pte bits in __supported_pte_mask
xen: Use wmb instead of rmb in xen_evtchn_do_upcall().
x86: fix NULL pointer deref in __switch_to
There is a race in the COW logic. It contains a shortcut to avoid the
COW and reuse the page if we have the sole reference on the page,
however it is possible to have two racing do_wp_page()ers with one
causing the other to mistakenly believe it is safe to take the shortcut
when it is not. This could lead to data corruption.
Process 1 and process2 each have a wp pte of the same anon page (ie.
one forked the other). The page's mapcount is 2. Then they both
attempt to write to it around the same time...
proc1 proc2 thr1 proc2 thr2
CPU0 CPU1 CPU3
do_wp_page() do_wp_page()
trylock_page()
can_share_swap_page()
load page mapcount (==2)
reuse = 0
pte unlock
copy page to new_page
pte lock
page_remove_rmap(page);
trylock_page()
can_share_swap_page()
load page mapcount (==1)
reuse = 1
ptep_set_access_flags (allow W)
write private key into page
read from page
ptep_clear_flush()
set_pte_at(pte of new_page)
Fix this by moving the page_remove_rmap of the old page after the pte
clear and flush. Potentially the entire branch could be moved down
here, but in order to stay consistent, I won't (should probably move all
the *_mm_counter stuff with one patch).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 89f5b7da2a ("Reinstate ZERO_PAGE
optimization in 'get_user_pages()' and fix XIP") broke vmware, as
reported by Jeff Chua:
"This broke vmware 6.0.4.
Jun 22 14:53:03.845: vmx| NOT_IMPLEMENTED
/build/mts/release/bora-93057/bora/vmx/main/vmmonPosix.c:774"
and the reason seems to be that there's an old bug in how we handle do
FOLL_ANON on VM_SHARED areas in get_user_pages(), but since it only
triggered if the whole page table was missing, nobody had apparently hit
it before.
The recent changes to 'follow_page()' made the FOLL_ANON logic trigger
not just for whole missing page tables, but for individual pages as
well, and exposed this problem.
This fixes it by making the test for when FOLL_ANON is used more
careful, and also makes the code easier to read and understand by moving
the logic to a separate inline function.
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialize the value used for the confounder to a random value
rather than starting from zero.
Allow for confounders of length 8 or 16 (which will be needed for AES).
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The gss_krb5_crypto.o object belongs in the rpcsec_gss_krb5 module.
Also, there is no need to export symbols from gss_krb5_crypto.c
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
cleanup:
Document token header size with a #define instead of open-coding it.
Don't needlessly increment "ptr" past the beginning of the header
which makes the values passed to functions more understandable and
eliminates the need for extra "krb5_hdr" pointer.
Clean up some intersecting white-space issues flagged by checkpatch.pl.
This leaves the checksum length hard-coded at 8 for DES. A later patch
cleans that up.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
I noted that the 'struct tty_struct *real_tty' is not used in this
function, so I removed the code about 'real_tty'.
Signed-off-by: Gustavo Fernando Padovan <gustavo@las.ic.unicamp.br>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the requirement rules are now more relaxed. Also correct a
contradiction in the previous update
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following sparse warnings:
fs/dcache.c:2183:19: warning: symbol 'filp_cachep' was not declared. Should it be static?
fs/dcache.c:115:3: warning: context imbalance in 'dentry_iput' - unexpected unlock
fs/dcache.c:188:2: warning: context imbalance in 'dput' - different lock contexts for basic block
fs/dcache.c:400:2: warning: context imbalance in 'prune_one_dentry' - different lock contexts for basic block
fs/dcache.c:431:22: warning: context imbalance in 'prune_dcache' - different lock contexts for basic block
fs/dcache.c:563:2: warning: context imbalance in 'shrink_dcache_sb' - different lock contexts for basic block
fs/dcache.c:1385:6: warning: context imbalance in 'd_delete' - wrong count at exit
fs/dcache.c:1636:2: warning: context imbalance in '__d_unalias' - unexpected unlock
fs/dcache.c:1735:2: warning: context imbalance in 'd_materialise_unique' - different lock contexts for basic block
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The path that __d_path() computes can become slightly inconsistent when it
races with mount operations: it grabs the vfsmount_lock when traversing mount
points but immediately drops it again, only to re-grab it when it reaches the
next mount point. The result is that the filename computed is not always
consisent, and the file may never have had that name. (This is unlikely, but
still possible.)
Fix this by grabbing the vfsmount_lock for the whole duration of
__d_path().
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: John Johansen <jjohansen@suse.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Rename nfsd_permission() specific MAY_* flags to NFSD_MAY_* to make it
clear, that these are not used outside nfsd, and to avoid name and
number space conflicts with the VFS.
[comment from hch: rename MAY_READ, MAY_WRITE and MAY_EXEC as well]
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
OCFS2 can return -ERESTARTSYS from write requests (and possibly
elsewhere) if there is a signal pending.
If nfsd is shutdown (by sending a signal to each thread) while there
is still an IO load from the client, each thread could handle one last
request with a signal pending. This can result in -ERESTARTSYS
which is not understood by nfserrno() and so is reflected back to
the client as nfserr_io aka -EIO. This is wrong.
Instead, interpret ERESTARTSYS to mean "try again later" by returning
nfserr_jukebox. The client will resend and - if the server is
restarted - the write will (hopefully) be successful and everyone will
be happy.
The symptom that I narrowed down to this was:
copy a large file via NFS to an OCFS2 filesystem, and restart
the nfs server during the copy.
The 'cp' might get an -EIO, and the file will be corrupted -
presumably holes in the middle where writes appeared to fail.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
We need the nfsd_mutex before accessing nfsd_serv->sv_nrthreads or we
can't even guarantee nfsd_serv will still be there.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
If lockd_down is called very rapidly after lockd_up returns, then
there is a slim chance that lockd() will never be called. kthread()
will return before calling the function, so we'll end up never
actually calling the cleanup functions for the thread.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Since we no longer make any distinction between shutdown signals with
nfsd, then it becomes easier to just standardize on a particular signal
to use to bring it down (SIGINT, in this case).
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This patch is rather large, but I couldn't figure out a way to break it
up that would remain bisectable. It does several things:
- change svc_thread_fn typedef to better match what kthread_create expects
- change svc_pool_map_set_cpumask to be more kthread friendly. Make it
take a task arg and and get rid of the "oldmask"
- have svc_set_num_threads call kthread_create directly
- eliminate __svc_create_thread
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The special handling for SIGHUP in knfsd is a holdover from much
earlier versions of Linux where reloading the export table was
more expensive. That facility is not really needed anymore and
to my knowledge, is seldom-used.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>