Fixes to USART setup on the stk-1000 ... don't configure USART 2, since
its TXD/RXD are used for INT-A and INT-B buttons; and configure USART 0
(for IRDA, and with corrected IRQ) iff SW2 has a non-default setting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The /proc/interrupts file should also display the irq_chip associated
with each irq ... e.g. INTC, EIM, GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rename the 'us_regs' field of the ucc_slow_info structure in ucc_slow.h
to just 'regs'. The equivalent field in the ucc_fast_info structure is
also called 'regs', so this patch makes them comparable, and makes the
code a little easier to read, because there already is a 'us_regs' in
another ucc_slow structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the old IUCV code from drivers/s390/net
Remove approprirate IUCV entries from drivers/s390/net/Makefile,
drivers/s390/net/Kconfig and arch/s390/defconfig
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unconditionally disabling the PCKs (Programmable Clocks) is not a good
idea as it breaks boards that depend on those clocks being enabled by
bootloaders.
Therefore only disable unused clocks late in the init process, giving
the board init code the chance to claim the clock.
Patch from Steven Scholz.
Since the HCK clocks on SAM9261 are already being registered as a
independent clocks, we don't need the special case for HCK0 on the
SAM9261. Platform-init code and drivers should use the clock API to
enable/disable the clock.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Other platforms other than SMP may have an outer cache. For these, we
also need to mark the page table walks outer cacheable. Since marking
the walks always outer cacheable apparantly has no side effects, we
might as well always mark them so.
However, we continue to only mark PTWs shared if we have SMP enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (116 commits)
[POWERPC] Add export of vgacon_remap_base
[POWERPC] Remove bogus comment about page_is_ram
[POWERPC] windfarm: don't die on suspend thread signal
[POWERPC] Fix comment in kernel/irq.c
[POWERPC] ppc: Fix booke watchdog initialization
[POWERPC] PPC: Use ARRAY_SIZE macro when appropriate
[POWERPC] Use ARRAY_SIZE macro when appropriate
[POWERPC] Fix ppc64's writing to struct file_operations
[POWERPC] ppc: use syslog macro for the printk log level
[POWERPC] ppc: cs4218_tdm remove extra brace
[POWERPC] Add mpc52xx/lite5200 PCI support
[POWERPC] Only use H_BULK_REMOVE if the firmware supports it
[POWERPC] Fixup error handling when emulating a floating point instruction
[POWERPC] Enable interrupts if we are doing fp math emulation
[POWERPC] Added kprobes support to ppc32
[POWERPC] Make pSeries use the H_BULK_REMOVE hypervisor call
[POWERPC] Clear RI bit in MSR before restoring r13 when returning to userspace
[POWERPC] Fix performance monitor exception
[POWERPC] Compile fixes for arch/powerpc dcr code
[POWERPC] Maple: use mmio nvram
...
In consistent_sync(), start + size can end up pointing one byte
beyond the end of the direct RAM mapping. We shouldn't BUG() when
this happens.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO pin setup should be handed by the platform-setup code, and not
directly by the driver.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an overrun in the AT91SAM9 gettimeoffset() function. This causes
the time value returned by gettimeofday() to jump "backwards".
Original patch from Michel Benoit.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the Timer/Counter Unit clocks on the AT91RM9200, AT91SAM9260 and
AT91SAM9261 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263-EK board.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263 processor. It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.
These changes are:
* The system peripheral I/O region we remap has increased from
0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
* The increased I/O region forces changes to entry-macro.S and
debug-macro.S due to ARM's limited immediate offset addressing
modes.
* Maximum number of GPIO banks increases to 5.
* 2 MMC controllers so the board-setup code needs to specify which
controller it wishes to use when calling at91_add_device_mmc().
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix build failure of AT91SAM9260.
The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a
"struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263)
ethernet driver (macb.c) [developed on the AVR32 architecture] expects a
"struct eth_platform_data".
Since the platform data of the two drivers is very similar, we continue
to use the "struct at91_eth_data" for all AT91 processors but add a
#define eth_platform_data at91_eth_data
in board.h to keep the MACB driver happy.
Original patch by Jan Altenberg.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA cache handling functions take virtual addresses, but in the
form of unsigned long arguments. This leads to a little confusion
about what exactly they take. So, convert them to take const void *
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The outer cache can be L2 as on RealView/EB MPCore platform or even L3
or further on ARMv7 cores. This patch adds the generic support for
flushing the outer cache in the DMA operations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Memory allocated by the coherent memory allocators will be marked
uncacheable, which means it's pointless calling consistent_sync()
to perform cache maintainence on this memory; it's just a waste of
CPU cycles.
Moreover, with the (subsequent) merge of outer cache support, it
actually breaks things to call consistent_sync() on anything but
direct-mapped memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The architecture specification states that TLB operations are
guaranteed to be complete only after the execution of a DSB (Data
Synchronisation Barrier, former Data Write Barrier or Drain Write
Buffer). The branch target cache invalidation is also needed. The ISB
(Instruction Synchronisation Barrier, formerly Prefetch Flush) is
needed unless there will be a return from exception before the
corresponding mapping is used (i.e. user mappings).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On newer architectures (ARMv6, ARMv7), the depth of the prefetch and
branch prediction is implementation defined and there is a small risk
of wrong ASID tagging when changing TTBR0 before setting the new
context id. The recommended solution is to set a reserved ASID during
TTBR changing. This patch reserves ASID 0.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up proc-xsc3:
- Correct a number of typos.
- Fix up indentation in a number of places.
- Change references to the various caches to be more clear about
whether we're talking about the L1 D, the L1 I or the unified L2
cache.
- Rename "drain write buffer" to "data write barrier", the official
name used in the Manzano manual.
- Change the xsc3 cpu name from "XScale-Core3" to "XScale-V3 based
processor".
Also, since a previously merged patch implements proper support for
using a MAC or iWMMXt coprocessor on xsc3 platforms, we no longer
need to enable access to CP0 on boot.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the i2c-pxa driver to actually using the platform device information and let it handle the power i2c bus on pxa27x too. Original version of this patch didn't compile with CONFIG_I2C_PXA_SLAVE set.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_device setup code for OTG/peripheral mode of 834x DR module.
It is needed for USB client driver to work.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board specific initialization code for USB to work in both MPH and DR
mode for MPC8349E MDS-PB board.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added a new dr_mode property to describe what mode the DR controller is being
used in (host, device, OTG). Updated the MPC8349E MDS dts with this new property.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8313E Reference Development Board (RDB). The board
is a mini-ITX reference board with 128M DDR2, 8M flash, 32M NAND, USB, PCI,
gigabit ethernet, and serial.
Signed-off-by: Wilson Lo <Wilson.Lo@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following macro :
include/asm-powerpc/vga.h:#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
is used by drivers/video/console/vgacon.c which can be compiled as a module
(drivers/video/vga16fb.ko).
Therefore, vgacon_remap_base should be exported.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/mm/mem.c states that page_is_ram is called by the code that
implements /dev/mem, which isn't true. Remove the comment.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kernel/irq.c contains a comment that speaks of -1 and -2 as interrupt
numbers, but this is actually dependent on configuration options now.
Replace by NO_IRQ and NO_IRQ_ENABLED.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (70 commits)
USB: remove duplicate device id from zc0301
USB: remove duplicate device id from usb_storage
USB: remove duplicate device id from keyspan
USB: remove duplicate device id from ftdi_sio
USB: remove duplicate device id from visor
USB: a bit more coding style cleanup
usbcore: trivial whitespace fixes
usb-storage: use first bulk endpoints, not last
EHCI: fix interrupt-driven remote wakeup
USB: switch ehci-hcd to new polling scheme
USB: autosuspend for usb printer driver
USB Input: Added kernel module to support all GTCO CalComp USB InterWrite School products
USB: Sierra Wireless auto set D0
USB: usb ethernet gadget recognizes HUSB2DEV
USB: list atmel husb2_udc gadget controller
USB: gadgetfs AIO tweaks
USB: gadgetfs behaves better on userspace init bug
USB: gadgetfs race fix
USB: gadgetfs simplifications
USB: gadgetfs cleanups
...
