TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use rtc-rs5c348 and at25 spi protocol driver and spi_txx9 spi
controller driver instead of platform dependent codes.
This patch also removes dependencies to old RTC interfaces such as
rtc_mips_get_time, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to break the code of people who think they are supposed to scribble
into the pci device structure - it's off limits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable Cobalt button support and change ATA driver from BLK_DEV_VIA82CXXX
to PATA_VIA..
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert old/obsolete NORET_TYPE and ATTRIB_NORET macros to use the
newer standard of "__noreturn" as defined in compiler-gcc.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use standard missing-syscalls with EXTRA_CFLAGS instead of duplicating
the command. And move the archprepare rule before the archclean rule.
Suggested by Franck Bui-Huu. Also add "echo" to show the target ABI.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Check to make sure ppc_md.init_IRQ has been set before calling it.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Found 2 instances of return one right after each other in
arch_add_memory(). This removes the superfluous one.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Disable auto-select of CONFIG_EMBEDDED. ELECTRA_IDE selects
PATA_PLATFORM which should be sufficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the pasemi platform to "pasemi" to be in line with the
platform's directory name.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With !CONFIG_NUMA, these are static inlines in the header file so
don't generate exports for them in that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When booting a current kernel with CONFIG_PRINTK_TIME enabled you'll
see messages like:
[ 0.000000] time_init: decrementer frequency = 188.044000 MHz
[ 0.000000] time_init: processor frequency = 1504.352000 MHz
[3712914.436297] Console: colour dummy device 80x25
This cause by the initialisation of tb_to_ns_scale in time_init(), suddenly the
multiplication in sched_clock() now does something :). This patch modifies
sched_clock() to report the offset since the machine booted so the same
printk's now look like:
[ 0.000000] time_init: decrementer frequency = 188.044000 MHz
[ 0.000000] time_init: processor frequency = 1504.352000 MHz
[ 0.000135] Console: colour dummy device 80x25
Effectivly including the uptime in printk()s.
This patch makes tb_to_ns_scale and tb_to_ns_shift static and
read_mostly for good measure.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This simply prevents a build error if no platform is selected.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to build the PS3 flash rom image and remove some unneeded
lmb calls.
The PS3's lv1 loader supports loading gzipped binary images from flash
rom to addr zero. The loader enters the image at addr 0x100.
In this implementation a bootwrapper overlay is use to arrange for the
kernel to be loaded to addr zero and to have a suitable bootwrapper
entry at 0x100. To construct the rom image, 0x100 bytes from offset
0x100 in the kernel is copied to the bootwrapper symbol
__system_reset_kernel. The 0x100 bytes at the bootwrapper symbol
__system_reset_overlay is then copied to offset 0x100. At runtime the
bootwrapper program copies the 0x100 bytes at __system_reset_kernel to
addr 0x100.
zImage.ps3 is a wrapped image that contains a flat device tree, an lv1
compatible entry point, and an optional initrd. otheros.bld is the gzip
compresed rom image built from zImage.ps3. otheros.bld is suitable for
programming into the PS3 boot flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Oprofile enhanced instruction sampling support.
When performing instruction sampling, the mmcra[SLOT] field can be used to
more accurately identify the address of the sampled instruction.
Tested on power4, js20, power5 and power5+.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
cc: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The prom.c debugging code creates a "powerpc" directory in debugfs,
which is nice, but doesn't allow any other debugging code to stick things
under "powerpc" in debugfs. So make it global.
While we're there we should make the prom.c debugging code depend on
CONFIG_DEBUG_FS, because it doesn't work otherwise.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The device tree for the MPC8641 HPCN does not implement the device type
property for I8042 nodes.
In addition to checking the I8042 node's device type, also match the
keyboard and/or mouse nodes' compatible property.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the refcount for a device node goes to 0, we call the
destructor - of_node_release(). This should only happen if we've
already detached the node from the device tree.
So add a flag OF_DETACHED which tracks detached-ness, and if we
find ourselves in of_node_release() without it set, issue a
warning and don't free the device_node. To avoid warning
continuously reinitialise the kref to a sane value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The struct device_node currently has a _flags variable, although
it's only used for one flag - OF_DYNAMIC. Generalise the flag
accessors so we can use them with other flags in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
