At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port. That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses. In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards). It doesn't make sense for userspace to change
these settings.
Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure. If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.
In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial driver patch for the PMC-Sierra MSP71xx devices.
There are three different fixes:
1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
16550 in that the THRE interrupt will not re-assert itself simply by
disabling and re-enabling the THRI bit in the IER, it is only re-enabled
if a character is actually sent out.
It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
also fixes it so we have dropped our initial workaround. This patch now
needs to be applied on top of that "mm" patch.
2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
which causes a new Busy Detect interrupt to be generated if it's busy
when the LCR is written. This fix saves the value of the LCR and
rewrites it after clearing the interrupt.
3 Workaround for interrupt/data concurrency issue: The SoC needs to
ensure that writes that can cause interrupts to be cleared reach the UART
before returning from the ISR. This fix reads a non-destructive register
on the UART so the read transaction completion ensures the previously
queued write transaction has also completed.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was broken. It adds complexity, for no good reason. Rather than
separate __pa() and __pa_symbol(), we should deprecate __pa_symbol(),
and preferably __pa() too - and just use "virt_to_phys()" instead, which
is more readable and has nicer semantics.
However, right now, just undo the separation, and make __pa_symbol() be
the exact same as __pa(). That fixes the bugs this patch introduced,
and we can do the fairly obvious cleanups later.
Do the new __phys_addr() function (which is now the actual workhorse for
the unified __pa()/__pa_symbol()) as a real external function, that way
all the potential issues with compile/link-time optimizations of
constant symbol addresses go away, and we can also, if we choose to, add
more sanity-checking of the argument.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ppc4xx_sgdma.c is #including asm/dma-mapping.h directly, which should
only ever be included via linux/dma-mapping.h. asm/dma-mapping.h
relies on an enum defined in linux/dma-mapping.h before its own
include. This fixes the problem.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement deep-sleep on MPC52xx.
SDRAM is put into self-refresh with help of SRAM code
(alternatives would be code in FLASH, I-cache).
Interrupt code must also not be in SDRAM, so put it
in I-cache.
MPC52xx core is static, so contents will remain intact even
with clocks turned off.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device type should be "soc" (as in lite5200.dts), compatible is
already set to "mpc5200".
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently other parts of the kernel need to know the
modalias internally (like the sysfs code in macintosh driver).
To avoid consistency issues, we export this code and use it
everywhere it's needed rather than repeat it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a couple of missing dependencies in
arch/powerpc/boot/Makefile. First, it ensures that the zlib.h header
is linked in before attempting to build gunzip_util.o, as it is,
building gunzip_util.o usually works, but not always depending on make
order.
Second, it makes the final images which are built using a dts
dependent on that dts, so the image will be correctly rebuilt if the
dts changes. This in turn requires fixing the definition of the dts
variable. CONFIG_DEVICE_TREE from Kconfig will have quotes around it,
which don't matter when passing the variable to a shell, but which
need to be removed when incorporating it into a filename for make's
use.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the global cpu speed variable according to current cpufreq speed,
/proc/cpuinfo reports the actual speed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powermac G5 suspend to disk implementation. The code is platform
agnostic but only tested on powermac, no other 64-bit powerpc
machines.
Because nvidiafb still breaks suspend I have marked it EXPERIMENTAL on
powermac and because I can't test it and some lowlevel code will need
changes it is BROKEN on all other 64-bit platforms.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows the zImage target to once again be used to build
all supported image types, rather than requiring an explicit
"make uImage" to avoid failing to create an unneeded cuImage.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new function named smp_call_function_single(). This matches a generic
prototype from include/linux/smp.h.
Add a function smp_call_function_map(). This is, for the most part, a rename
of smp_call_function, with some added cpumask support. smp_call_function and
smp_call_function_single call into smp_call_function_map.
Lightly tested on 970mp (blade), power4 and power5.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the powerpc version of topology_init() from an __initcall to
a subsys_initcall to match all other architectures.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds mpic to the system devices and implements suspend
and resume for them. This is necessary to get interrupts for
modules back to where they were before a suspend to disk.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a couple of kexec problems related to 64K page
support in the kernel. kexec issues a tlbie for each pte. The
parameters for the tlbie are the page size and the virtual address.
Support was missing for the computation of these two parameters
for 64K pages. This adds that support.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
apb_calc_first_last(), apb_fake_ranges(), pci_of_scan_bus(),
of_scan_pci_bridge(), pci_of_scan_bus(), and pci_scan_one_pbm()
should all be __devinit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor refactoring in the generic code was necessary for
this:
1) This controller requires 8-byte access to the interrupt map
and clear register. They are 64-bits on all the other
SBUS and PCI controllers anyways, so this was easy to cure.
2) The IMAP register has a different layout and some bits that we
need to preserve, so use a read/modify/write when making
changes to the IMAP register in generic code.
3) Flushing the entire IOMMU TLB is best done with a single write
to a register on this PCI controller, add a iommu->iommu_flushinv
for this.
Still lacks MSI support, that will come later.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the shared APM emulation code being introduced, hp6xx was missed
in the conversion. Get it building again.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds more full-featured support for the SH7722 Solution Engine.
Previously this was using the generic board, and lacked most of the
peripheral support.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was done in cpuinfo, but with the number of clocks
growing, it makes more sense to place this in a different proc entry.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7722 (MobileR) to the clock framework.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the SH7780 PCIC on the Solution Engine 7780,
missing from the previous board-support patch.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we've been handling udivdi3 references and wrapping
them in to div64_32() automatically. This doesn't get a lot of
use, however, and as akpm noted in the recent thread on l-k:
http://lkml.org/lkml/2007/2/27/241
we're better off simply ripping it out and going the do_div()
route if there happen to be any places that need it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks some of the node 0 bootmem initialization in
preparation for discontigmem and sparsemem support.
ARCH_POPULATES_NODE_MAP is switched to as a result of this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the L-BOX RE2 router.
http://www.nttcom.co.jp/l-box/
L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.
The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updates for the landisk board:
- The push_switch framework was used.
- landisk_pwb.c was divided into psw.c and gio.c.
- pata_platform was supported in USL-5P.
- irq.c was rewritten.
- io.c was replaced with generic I/O routines.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
