The iWARP connection manager uses the ib_addr services to do route
resolution (neighbour discovery in the IP world). The ib_addr
netevent callback routine, however, currently only acts on InfiniBand
neighbour updates. It needs to act on ethernet neighbour updates as
well.
This patch just removes filtering on device type altogether and will
trigger on any neighour updates where the nud_type is valid. This
simplifies the code some.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When there is a call to send_tsk_mgmt SRP posts a send and waits for 5
seconds to get a response.
When the QP is in the error state it is obvious that there will be no
response so it is quite useless to wait. In fact, the timeout causes
SRP to wait a long time to reconnect when a QP error occurs. (Each
abort and each reset_device calls send_tsk_mgmt, which waits for the
timeout). The following patch solves this problem by identifying the
failure and returning an immediate error code.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_wc currently only includes the local QP number: this matches
the IB spec, but seems mostly useless. The following patch replaces
this with the pointer to qp itself, and updates all low level drivers
and all users.
This has the following advantages:
- Ability to get a per-qp context through wc->qp->qp_context
- Existing drivers already have the qp pointer ready in poll cq, so
this change actually saves a tiny bit (extra memory read) on data path
(for ehca it would actually be expensive to find the QP pointer when
polling a CQ, but ehca does not support SRQ so we can leave wc->qp as
NULL for ehca)
- Users that need the QP number can still get it through wc->qp->qp_num
Use case:
In IPoIB connected mode code, I have a common CQ shared by multiple
QPs. To track connection usage, I need a way to get at some per-QP
context upon the completion, and I would like to avoid allocating
context object per work request just to stick a QP pointer into it.
With this code, I can just use wc->qp->qp_context.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC high-speed, wide bus support and SD high-speed
are functions that aren't critical for correct
operation of the card. As such, they shouldn't mark
the card as bad or dead when there is a failure
activating these features.
This is needed in particular on some really stupid
hardware (e.g. Winbond's) where not all data transfer
commands are supported.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The wbsd hardware is so incredibly brain damaged that it has an internal
list of commands that result in data transfers. The result being that
commands that aren't on this list aren't supported.
Instead of locking up, waiting for a data interrupt that will never come,
we try to fail a bit more gracefully.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Many controllers have an upper limit on the number of blocks that can be
transferred in one request. Allow the host drivers to specify this and make
sure we avoid hitting this limit.
Also change the max_sectors field to avoid confusion. This makes it map
less directly to the block layer limits, but as they didn't apply directly
on MMC cards anyway, this isn't a great loss.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most controllers have an upper limit on the block size. Allow the host
drivers to specify this and make sure we avoid hitting this limit.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix some spaces and tabs. No semantic changes are introduced.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch also adds symbolic defines for supported pci ids.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As there's only one work item (media_switcher) to handle and it's effectively
serialized with itself, I found it more convenient to use kthread instead of
workqueue. This also allows for a working implementation of suspend/resume,
which were totally broken in the past version.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Hardware does not say whether card was inserted or removed when reporting
socket events. Moreover, during suspend, media can be removed or switched
to some other card type without notification. Therefore, for each socket
in the change set the following is performed:
1. If there's active device in the socket it's unregistered
2. Media detection is performed
3. If detection recognizes supportable media, new device is registered
This patch also alters some macros and variable names to enhance clarity.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Eject function can take advantage of the socket_id field instead of explicit
pointer comparison.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch introduces no semantic changes - it is here for estetic purposes.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In order to support correct suspend and resume several changes were needed:
1. Switch from work_struct to tasklet for command handling. When device
suspend is called workqueues are already frozen and can not be used.
2. Separate host initialization code from driver's probe and don't rely
on interrupts for host initialization. This, in turn, addresses two
problems:
a) Resume needs to re-initialize the host, but can not assume that
device interrupts were already re-armed.
b) Previously, probe will return successfully before really knowing
the state of the host, as host interrupts were not armed in time.
Now it uses polling to determine the real host state before returning.
3. Separate termination code from driver's remove. Termination may be caused
by resume, if media changed type or became unavailable during suspend.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The register access order when setting hardware timeout was incorrect and
causing problems (wrong timeout intervals). This is now fixed.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Two changes are introduced to software timeout handler in order to simplify
its management:
1. The implementation is switched from work_struct to timer
2. Previously, software timeout was rearmed with each interrupt. Now,
current request must complete entirely within timeout interval.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Data buffer for PIO transfer used to be mapped in advance with kmap.
Abolish it in favor of on-demand kmap_atomic.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Previously, stop command was issued right after BRS (block received/sent)
event. Stop command completion event could interfere with the card busy
event, causing miscount of the written blocks.
This patch ensures that stop command issued as last action for a
particular command, after DMA sompletion event and written block
count verification.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to the generous donation of an SDHC card by John Gilmore, and
the surprisingly enlightened decision by the SD Card Association to
publish useful specs, I've been able to bash out support for SDHC. The
changes are not too profound:
i) Add a card flag indicating the card uses block level addressing and
check it in the block driver. As we never took advantage of byte-level
addressing, this simply involves skipping the block -> byte
translation when sending commands.
ii) The layout of the CSD is changed - a set of fields are discarded
to make space for a larger C_SIZE. We did not reference any of the
discarded fields except those related to the C_SIZE.
iii) Read and write timeouts are fixed values and not calculated from
CSD values.
iv) Before invoking SEND_APP_OP_COND, we must invoke the new
SEND_IF_COND to inform the card we support SDHC.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for these devices was broken for 2.6.18-rc1 and later by commit
146ad66eac, which added voltage level support.
This restores the previous behaviour for these devices by ensuring that when
the voltage is changed, only one write to set the voltage is performed.
It may be that both writes are needed if the voltage is being changed between
two non-zero values or that it's safe to ensure that only one write is done
if the hardware only supports one voltage; I don't know whether either is the
case nor can I test since I have only the one SD reader (1524:0550), and it
supports just the one voltage.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change the parent of cards to be a specific host (a class
device), not the physical controller. This is particularly
useful when the hardware has multiple slots, meaning
multiple hosts.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As card_busy was only used to indicate if the host was exclusively
claimed and not really used to identify a particular card, replacing
it with just a boolean makes things a lot more easily understandable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch allows drm to populate an agpgart structure with pages of its own.
It's needed for the new drm memory manager which dynamically flips pages in and out of AGP.
The patch modifies the generic functions as well as the intel agp driver. The intel drm driver is
currently the only one supporting the new memory manager.
Other agp drivers may need some minor fixing up once they have a corresponding memory manager enabled drm driver.
AGP memory types >= AGP_USER_TYPES are not populated by the agpgart driver, but the drm is expected
to do that, as well as taking care of cache- and tlb flushing when needed.
It's not possible to request these types from user space using agpgart ioctls.
The Intel driver also gets a new memory type for pages that can be bound cached to the intel GTT.
Signed-off-by: Thomas Hellstrom <thomas@tungstengraphics.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The following video card requires the agpgart driver ioctl
interface in order to detect video memory.
00:02.0 VGA compatible controller: Intel Corporation Mobile
945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)
Tested on a Thinkpad Z61t, Xorg.0.log from a 32bit debian Xorg is at;
http://montezuma.homeunix.net/Xorg.0.log
Signed-off-by: Zwane Mwaikambo <zwane@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
These changes work compatibly with the old V17 firmware
Contribution:
Ed Chim <ed_chim@adaptec.com>
Gilbert Wu <gilbert_wu@adaptec.com>
Change Log:
1. Use dword instead of qword to display the value of Connection
State register for debug purpose.
2. There are some registers location of AIC94xx chip has been changed
according to the new V28 firmware. The patch has redefined the register
location and provided initialization.
3. The new sequencer firmware v28 for Aic94xx SAS/SATA Linux open
source device driver can be downloaded from
http://www.adaptec.com/NR/exeres/35B611BC-9789-4B5B-82C6-85A2CCA8A46A.htm
Signed-off-by: Gilbert Wu <gilbert_wu@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
[SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
[SCSI] qla4xxx: bug fixes
[SCSI] Fix scsi_add_device() for async scanning
If an EH command times out today, the LLDD's abort handler
will be called to abort the command. It is assumed that this
completes successfully, which can result in the command getting
completed later resulting in an oops. Improve the current
implementation by escalating all the way to host reset if
necessary in order to clean up the EH command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In asd_initiate_ssp_tmf, the TMF result code is replaced with
TMF_RESP_FUNC_FAILED except when the TMF returns a result code immediately.
However, TMFs can return result codes via an ESCB... yet these codes are
also replaced with "FAILED". The only values that can fall into that case
are TMF_* codes anyway, so get rid of this code where COMPLETE and SUCCESS
are turned into FAILED. This also lets us propagate those TMF_* codes up
to the caller.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsas: Don't BUG when connecting two expanders via wide port
When a device is connected to an expander, the discovery process goes through
sas_ex_discover_dev to figure out what's attached to the phy. If it is the
case that the phy being discovered happens to be the second phy of a wide link
to an expander, that discover_dev function will incorrectly call
sas_ex_discover_expander, which creates another sas_port and tries to attach the
other sas_phys to the new port, thus triggering a BUG. The correct thing to do is
to check the other ex_phys of the expander to see if there's a sas_port for this
sas_phy, and attach the sas_phy to the existing sas_port.
This is easily triggered if one enables the phys of a wide port between
expanders one by one.
This second version of the patch fixes a small regression in the case where
all the phys show up at once and we accidentally try to attach to a port
that hasn't been created yet.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Thu, 1 Feb 2007, Andrew Morton wrote:
> On Thu, 1 Feb 2007 15:34:29 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7919
> >
> > Summary: Tape dies if wrong block size used
> > Kernel Version: 2.6.20-rc5
> > Status: NEW
> > Severity: normal
> > Owner: scsi_drivers-other@kernel-bugs.osdl.org
> > Submitter: dmartin@sccd.ctc.edu
> >
> >
> > Most recent kernel where this bug did *NOT* occur: 2.6.17.14
> >
> > Other Kernels Tested and Results:
> >
> > OK 2.6.15.7
> > OK 2.6.16.37
> > OK 2.6.17.14
> > BAD 2.6.18.6
> > BAD 2.6.18-1.2869.fc6
> > BAD 2.6.19.2 +
> > BAD 2.6.20-rc5
> >
> > NOTE: 2.6.18-1.2869.fc6 is a Fedora modified kernel, all others are from kernel.org
> >
...
> > Steps to reproduce:
> > Get a Adaptec AHA-2940U/UW/D / AIC-7881U card and a tape drive,
> > install a recent kernel
> > set the tape block size - mt setblk 4096
> > read from or write to tape using wrong block size - tar -b 7 -cvf /dev/tape foo
> >
Write does not trigger this bug because the driver refuses in fixed block
mode writes that are not a multiple of the block size. Read does trigger
it in my system.
The bug is not associated with any specific HBA. st tries to do direct i/o
in fixed block mode with reads that are not a multiple of tape block size.
The patch in this message fixes the st problem by switching to using the
driver buffer up to the next close of the device file in fixed block mode
if the user asks for a read like this.
I don't know why the bug has surfaced only after 2.6.17 although the st
problem is old. There may be another bug in the block subsystem and this
patch works around it. However, the patch fixes a problem in st and in
this way it is a valid fix.
This patch may also fix the bug 7900.
The patch compiles and is lightly tested.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
