commit 05d43ed8a89c159ff641d472f970e3f1baa66318 upstream.
Now that the previous commit made it possible to do the personality
setting at the point of no return, we do just that for ELF binaries.
And suddenly all the reasons for that insane TIF_ABI_PENDING bit go
away, and we can just make SET_PERSONALITY() just do the obvious thing
for a 32-bit compat process.
Everything becomes much more straightforward this way.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
commit 18dce6ba5c8c6bd0f3ab4efa4cbdd698dab5c40a upstream.
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
Later all kind of devices fail...
and bisect it down to this commit:
commit b9c61b7007
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de>
Bisected-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4481374ce88ba8f460c8b89f2572027bd27057d0 upstream.
Sizing of memory allocations shouldn't depend on the number of physical
pages found in a system, as that generally includes (perhaps a huge amount
of) non-RAM pages. The amount of what actually is usable as storage
should instead be used as a basis here.
Some of the calculations (i.e. those not intending to use high memory)
should likely even use (totalram_pages - totalhigh_pages).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit dfea91d5a7c795fd6f4e1a97489a98e4e767463e upstream.
Chris McDermott from IBM confirmed that hurricane chipset in IBM summit
platforms doesn't support logical flat mode. Irrespective of the other
things like apic_id's, total number of logical cpu's, Linux kernel
should default to physical mode for this system.
The 32-bit kernel does so using the OEM checks for the IBM summit
platform. Add a similar OEM platform check for the 64bit kernel too.
Otherwise the linux kernel boot can hang on this platform under certain
bios/platform settings.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 557a701c16553b0b691dbb64ef30361115a80f64 upstream.
Easy fix for a regression introduced in 2.6.31.
On managed CPUs the cpufreq.c core will call driver->exit(cpu) on the
managed cpus and powernow_k8 will free the core's data.
Later driver->get(cpu) function might get called trying to read out the
current freq of a managed cpu and the NULL pointer check does not work on
the freed object -> better set it to NULL.
->get() is unsigned and must return 0 as invalid frequency.
Reference:
http://bugzilla.kernel.org/show_bug.cgi?id=14391
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 04a1e62c2cec820501f93526ad1e46073b802dc4 upstream.
The loop condition is fragile: we compare an unsigned value to zero, and
then decrement it by something larger than one in the loop. All the
callers should be passing in appropriately aligned buffer lengths, but
it's better to just not rely on it, and have some appropriate defensive
loop limits.
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 03a05ed1152944000151d57b71000de287a1eb02 upstream.
Currently, ARB_DISABLE is a NOP on all of the recent Intel platforms.
For such platforms, reduce contention on c3_lock by skipping the fake
ARB_DISABLE.
The cpu model id on one laptop is 14. If we disable ARB_DISABLE on this box,
the box can't be booted correctly. But if we still enable ARB_DISABLE on this
box, the box can be booted correctly.
So we still use the ARB_DISABLE for the cpu which mode id is less than 0x0f.
http://bugzilla.kernel.org/show_bug.cgi?id=14700
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upstream commit a2202aa29289db64ca7988b12343158b67b27f10.
On platforms where bios handles the thermal monitor interrupt,
APIC_LVTTHMR on each logical CPU is programmed to generate a SMI and OS
can't touch it.
Unfortunately AP bringup sequence using INIT-SIPI-SIPI clear all
the LVT entries except the mask bit. Essentially this results in
all LVT entries including the thermal monitoring interrupt set to masked
(clearing the bios programmed value for APIC_LVTTHMR).
And this leads to kernel take over the thermal monitoring interrupt
on AP's but not on BSP (leaving the bios programmed value only on BSP).
As a result of this, we have seen system hangs when the thermal
monitoring interrupt is generated.
Fix this by reading the initial value of thermal LVT entry on BSP
and if bios has taken over the control, then program the same value
on all AP's and leave the thermal monitoring interrupt control
on all the logical cpu's to the bios.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20091110013824.GA24940@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit bc09effabf0c5c6c7021e5ef9af15a23579b32a8 upstream.
mce_timer must be passed to setup_timer() in all cases, no
matter whether it is going to be actually used. Otherwise, when
the CPU gets brought down, its call to del_timer_sync() will
never return, as the timer won't have a base associated, and
hence lock_timer_base() will loop infinitely.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: <4B1DB831.2030801@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e02e0e1a130b9ca37c5186d38ad4b3aaf58bb149 upstream.
I double-checked the datasheet. One of the existing
descriptors has a typo: it should be 2MB not 2038 KB.
Signed-off-by: Dave Jones <davej@redhat.com>
LKML-Reference: <20091110200120.GA27090@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4528752f49c1f4025473d12bc5fa9181085c3f22 upstream.
On a multi-node x3950M2 system, there's a slight oddity in the
PCI device tree for all secondary nodes:
30:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
\-33:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01)
\-34:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04)
...as compared to the primary node:
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
\-01:00.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
03:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01)
\-04:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04)
In both nodes, the LSI RAID controller hangs off a CalIOC2
device, but on the secondary nodes, the BIOS hides the VGA
device and substitutes the device tree ending with the disk
controller.
It would seem that Calgary devices don't necessarily appear at
the top of the PCI tree, which means that the current code to
find the Calgary IOMMU that goes with a particular device is
buggy.
Rather than walk all the way to the top of the PCI
device tree and try to match bus number with Calgary descriptor,
the code needs to examine each parent of the particular device;
if it encounters a Calgary with a matching bus number, simply
use that.
Otherwise, we BUG() when the bus number of the Calgary doesn't
match the bus number of whatever's at the top of the device tree.
Extra note: This patch appears to work correctly for the x3950
that came before the x3950 M2.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Jon D. Mason <jdmason@kudzu.us>
Cc: Corinna Schultz <coschult@us.ibm.com>
LKML-Reference: <20091202230556.GG10295@tux1.beaverton.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4832ddda2ec4df96ea1eed334ae2dbd65fc1f541 upstream.
Bug reporter noted their system with an ASUS P4S800 motherboard would
hang when rebooting unless reboot=b was specified. Their dmidecode
didn't contain descriptive System Information for Manufacturer or
Product Name, so I used their Base Board Information to create a
reboot quirk patch. The bug reporter confirmed this patch resolves
the reboot hang.
Handle 0x0001, DMI type 1, 25 bytes
System Information
Manufacturer: System Manufacturer
Product Name: System Name
Version: System Version
Serial Number: SYS-1234567890
UUID: E0BFCD8B-7948-D911-A953-E486B4EEB67F
Wake-up Type: Power Switch
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: ASUSTeK Computer INC.
Product Name: P4S800
Version: REV 1.xx
Serial Number: xxxxxxxxxxx
BugLink: http://bugs.launchpad.net/bugs/366682
ASUS P4S800 will hang when rebooting unless reboot=b is specified.
Add a quirk to reboot through the bios.
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
LKML-Reference: <1259972107.4629.275.camel@emiko>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7d1849aff6687a135a8da3a75e32a00e3137a5e2 upstream.
The x86 lapic nmi watchdog does not recognize AMD Family 11h,
resulting in:
NMI watchdog: CPU not supported
As far as I can see from available documentation (the BKDM),
family 11h looks identical to family 10h as far as the PMU
is concerned.
Extending the check to accept family 11h results in:
Testing NMI watchdog ... OK.
I've been running with this change on a Turion X2 Ultra ZM-82
laptop for a couple of weeks now without problems.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <19223.53436.931768.278021@pilspetsen.it.uu.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9f800de38b05d84809e89f16671d636a140eede7 upstream.
This function may be called on the resume path and can not
be dropped after booting.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit be831297716036de5b24308447ecb69f1706a846 upstream.
For some devices the ACPI table may define unity map
requirements which must me met when the IOMMU is enabled. So
we need to attach devices to their domains as early as
possible so that these mappings are in place when needed.
This patch assigns the domains right after they are
allocated. Otherwise this can result in I/O page faults
before a driver binds to a device and BIOS is still using
it.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8dca15e40889e5d5e9655b03ba79c26200f760ce upstream.
"[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c"
changed the code to mistakenly pass the current cpu as the "processor"
argument of speedstep_get_frequency(), whereas it should be the type of
the processor.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14340
Based on a patch by Dave Mueller.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Dominik Brodowski <linux@brodo.de>
Reported-by: Dave Mueller <dave.mueller@gmx.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d77b81974521c82fa6fda38dfff1b491dcc62a32 upstream.
In commit 0de51088e6, we introduced the
use of acpi-cpufreq on VIA/Centaur CPU's by removing a vendor check for
VENDOR_INTEL. However, as it turns out, at least the Nano CPU's also
need the PDC (processor driver capabilities) handshake in order to
activate the methods required for acpi-cpufreq.
Since arch_acpi_processor_init_pdc() contains another vendor check for
Intel, the PDC is not initialized on VIA CPU's. The resulting behavior
of a current mainline kernel on such systems is: acpi-cpufreq
loads and it indicates CPU frequency changes. However, the CPU stays at
a single frequency
This trivial patch ensures that init_intel_pdc() is called on Intel and
VIA/Centaur CPU's alike.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ca0207114f1708b563f510b7781a360ec5b98359 upstream.
The function iommu_feature_disable is required on system
shutdown to disable the IOMMU but it is marked as __init.
This may result in a panic if the memory is reused. This
patch fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b417c9fd8690637f0c91479435ab3e2bf450c038 upstream.
If a system switches back and forth between hot and cold mode,
the MCE code will print a stream of critical kernel messages.
Extend the throttling code to properly notice this, by
only printing the first hot + cold transition and omitting
the rest up to CHECK_INTERVAL (5 minutes).
This way we'll only get a single incident of:
[ 102.356584] CPU0: Temperature above threshold, cpu clock throttled (total events = 1)
[ 102.357000] Disabling lock debugging due to kernel taint
[ 102.369223] CPU0: Temperature/speed normal
Every 5 minutes. The 'total events' count tells the number of cold/hot
transitions detected, should overheating occur after 5 minutes again:
[ 402.357580] CPU0: Temperature above threshold, cpu clock throttled (total events = 24891)
[ 402.358001] CPU0: Temperature/speed normal
[ 450.704142] Machine check events logged
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3967684006f30c253bc6d4a6604d1bad4a7fc672 upstream.
Instead of a mess of three separate percpu variables, consolidate
the state into a single structure.
Also clean up therm_throt_process(), use cleaner and more
understandable variable names and a clearer logic.
This, without changing the logic, makes the code more
streamlined, more readable and smaller as well:
text data bss dec hex filename
1487 169 4 1660 67c therm_throt.o.before
1432 176 4 1612 64c therm_throt.o.after
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c5cca146aa03e1f60fb179df65f0dbaf17bc64ed upstream.
There is an erratum for IOMMU hardware which documents
undefined behavior when forwarding SMI requests from
peripherals and the DTE of that peripheral has a sysmgt
value of 01b. This problem caused weird IO_PAGE_FAULTS in my
case.
This patch implements the suggested workaround for that
erratum into the AMD IOMMU driver. The erratum is
documented with number 63.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 036ed8ba61b72c19dc5759446d4fe0844aa88255 upstream.
A few parts of the uv_hub_info structure are initialized
incorrectly.
- n_val is being loaded with m_val.
- gpa_mask is initialized with a bytes instead of an unsigned long.
- Handle the case where none of the alias registers are used.
Lastly I converted the bau over to using the uv_hub_info->m_val
which is the correct value.
Without this patch, booting a large configuration hits a
problem where the upper bits of the gnode affect the pnode
and the bau will not operate.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Cc: Cliff Whickman <cpw@sgi.com>
LKML-Reference: <20091015224946.396355000@alcatraz.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 15b812f1d0a5ca8f5efe7f5882f468af10682ca8 upstream.
As reported in
http://bugzilla.kernel.org/show_bug.cgi?id=13940
on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them. It then apparently hits some undocumented resource conflict,
resulting in non-working devices.
Try to increase alignment to get more safe range for unassigned devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Resolved differently upstream in commit 8cab02dc3c58a12235c6d463ce684dded9696848
Ondrej Zary reported a suspend/resume hang with 2.6.31 in bug #14222.
http://bugzilla.kernel.org/show_bug.cgi?id=14222
The hang was bisected to c712184368
however, that was really just the last straw that caused the issue.
The problem was that on suspend, the PIT is removed as a clocksource,
and was using the mult value essentially as a is_enabled() flag. The
mult adjustments done in the commit above caused that usage to break,
causing bad list manipulation and the oops.
Further, on resume, the PIT clocksource is never restored, causing the
system to run in a degraded mode with jiffies as the clocksource.
This issue has since been resolved in 2.6.32-rc by commit
8cab02dc3c58a12235c6d463ce684dded9696848 which removes the clocksource
disabling on suspend. Testing shows no issues there.
So the following patch rectifies the situation for 2.6.31 users of the
PIT clocksource that use suspend and resume (which is probably not that
many).
Many thanks to Ondrej for helping narrow down what was happening, what
caused it, and verifying the fix.
---------------
Avoid using the unprotected clocksource.mult value as an "is_registered"
flag, instead us an explicit flag variable. This avoids possible list
corruption if the clocksource is double-unregistered.
Also re-register the PIT clocksource on resume so folks don't have to
use jiffies after suspend.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a20316d2aa41a8f4fd171648bad8f044f6060826 upstream.
The use of __pa() to calculate the address of a C-visible symbol
is wrong, and can lead to unpredictable results. See arch/x86/include/asm/page.h
for details.
It should be replaced with __pa_symbol(), that does the correct math here,
by taking relocations into account. This ensures the correct wallclock data
structure physical address is passed to the hypervisor.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6ba661787594868512a71c129062ebd57d0c01e7 upstream.
Commit b8bcfe997e made paravirt pte updates synchronous in interrupt
context.
Unfortunately the KVM pv mmu code caches the lazy/nonlazy mode
internally, so a pte update from interrupt context during a lazy mmu
operation can be batched while it should be performed synchronously.
https://bugzilla.redhat.com/show_bug.cgi?id=518022
Drop the internal mode variable and use paravirt_get_lazy_mode(), which
returns the correct state.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1ea0d14e480c245683927eecc03a70faf06e80c8 upstream.
The Intel Optimization Reference Guide says:
In Intel Atom microarchitecture, the address generation unit
assumes that the segment base will be 0 by default. Non-zero
segment base will cause load and store operations to experience
a delay.
- If the segment base isn't aligned to a cache line
boundary, the max throughput of memory operations is
reduced to one [e]very 9 cycles.
[...]
Assembly/Compiler Coding Rule 15. (H impact, ML generality)
For Intel Atom processors, use segments with base set to 0
whenever possible; avoid non-zero segment base address that is
not aligned to cache line boundary at all cost.
We can't avoid having a non-zero base for the stack-protector
segment, but we can make it cache-aligned.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <4AA01893.6000507@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 005155b1f626d2b2d7932e4afdf4fead168c6888 upstream.
For the x86_model to be greater than 6 or less than 12 is
logically always true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e0faf54ee82bf9c07f0307b4391caad4020bd659 upstream.
The amd_iommu_pd_table is indexed by protection domain
number and not by device id. So this check is broken and
must be removed.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2.6.31-rc7 does not boot on vSMP systems:
[ 8.501108] CPU31: Thermal monitoring enabled (TM1)
[ 8.501127] CPU 31 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
[ 8.650254] CPU31: Intel(R) Xeon(R) CPU E5540 @ 2.53GHz stepping 04
[ 8.710324] Brought up 32 CPUs
[ 8.713916] Total of 32 processors activated (162314.96 BogoMIPS).
[ 8.721489] ERROR: parent span is not a superset of domain->span
[ 8.727686] ERROR: domain->groups does not contain CPU0
[ 8.733091] ERROR: groups don't span domain->span
[ 8.737975] ERROR: domain->cpu_power not set
[ 8.742416]
Ravikiran Thirumalai bisected it to:
| commit 2759c3287d
| x86: don't call read_apic_id if !cpu_has_apic
The problem is that on vSMP systems the CPUID derived
initial-APICIDs are overlapping - so we need to fall
back on hard_smp_processor_id() which reads the local
APIC.
Both come from the hardware (influenced by firmware
though) so it's a tough call which one to trust.
Doing the quirk expresses the vSMP property properly
and also does not affect other systems, so we go for
this solution instead of a revert.
Reported-and-Tested-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shai Fultheim <shai@scalex86.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A944D3C.5030100@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevent: Prevent dead lock on clockevents_lock
timers: Drop write permission on /proc/timer_list
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix build with older binutils and consolidate linker script
x86: Fix an incorrect argument of reserve_bootmem()
x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile
xen: rearrange things to fix stackprotector
x86: make sure load_percpu_segment has no stackprotector
i386: Fix section mismatches for init code with !HOTPLUG_CPU
x86, pat: Allow ISA memory range uncacheable mapping requests
binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.
However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.
Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.
-v2: fix !SMP builds.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy. So
just warn if a caller gives us an empty mask, and ignore it.
This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:
http://bugzilla.kernel.org/show_bug.cgi?id=13933
which causes a silent lock-up. It only seems to happen on PPro, P2, P3
and Athlon XP cores. Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's. Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
load_percpu_segment() is used to set up the per-cpu segment registers,
which are also used for -fstack-protector. Make sure that the
load_percpu_segment() function doesn't have stackprotector enabled.
[ Impact: allow percpu setup before calling stack-protected functions ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.
This results in a deadlock in this scenario.
cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.
This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.
Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.
Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.
This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: use the right flag for get_vm_area()
percpu, sparc64: fix sparse possible cpu map handling
init: set nr_cpu_ids before setup_per_cpu_areas()
Commit 0e83815be7 changed the
section the initial_code variable gets allocated in, in an
attempt to address a section conflict warning. This, however
created a new section conflict when building without
HOTPLUG_CPU. The apparently only (reasonable) way to address
this is to always use __REFDATA.
Once at it, also fix a second section mismatch when not using
HOTPLUG_CPU.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
An older test-box started hanging at the following point during
bootup:
[ 0.022996] Mount-cache hash table entries: 512
[ 0.024996] Initializing cgroup subsys debug
[ 0.025996] Initializing cgroup subsys cpuacct
[ 0.026995] Initializing cgroup subsys devices
[ 0.027995] Initializing cgroup subsys freezer
[ 0.028995] mce: CPU supports 5 MCE banks
I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit
machine check code on 32bit"), which utilizes the MCE code on
32-bit systems too.
The problem is caused by this detail in my config:
# CONFIG_CPU_SUP_INTEL is not set
This disables the quirks in mce_cpu_quirks() but still enables
MCE support - which then hangs due to the missing quirk
workaround needed on this CPU:
if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0)
mce_banks[0].init = 0;
The safe solution is to not initialize MCEs if we dont know on
what CPU we are running (or if that CPU's support code got
disabled in the config).
Also be a bit more defensive on 32-bit systems: dont do a
boot-time dump of pending MCEs not just on the specific system
that we found a problem with (Pentium-M), but earlier ones as
well.
Now this problem is probably not common and disabling CPU
support is rare - but still being more defensive in something
we turned on for a wide range of CPUs is prudent.
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):
MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0
[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
and f200000000000115 (... READ Error).
To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
content of STATUS MSR before it is cleared during initialization. ]
Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.
The aim is to address the following section mismatch messages:
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.
WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.
WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The SGI UV Broadcast Assist Unit is used to send TLB shootdown
messages to remote nodes of the system. The header of the
message must contain the subnode id of the block in the
receiving hub that handles such messages. It should always be
0x10, the id of the "LB" block.
It had previously been documented as a "must be zero" field.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <E1Mc1x7-0005Ce-6t@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
percpu code has been assuming num_possible_cpus() == nr_cpu_ids which
is incorrect if cpu_possible_map contains holes. This causes percpu
code to access beyond allocated memories and vmalloc areas. On a
sparc64 machine with cpus 0 and 2 (u60), this triggers the following
warning or fails boot.
WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240()
Modules linked in:
Call Trace:
[00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240
[00000000004b1840] map_vm_area+0x20/0x60
[00000000004b1950] __vmalloc_area_node+0xd0/0x160
[0000000000593434] deflate_init+0x14/0xe0
[0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0
[00000000005844f0] crypto_alloc_base+0x50/0xa0
[000000000058b898] alg_test_comp+0x18/0x80
[000000000058dad4] alg_test+0x54/0x180
[000000000058af00] cryptomgr_test+0x40/0x60
[0000000000473098] kthread+0x58/0x80
[000000000042b590] kernel_thread+0x30/0x60
[0000000000472fd0] kthreadd+0xf0/0x160
---[ end trace 429b268a213317ba ]---
This patch fixes generic percpu functions and sparc64
setup_per_cpu_areas() so that they handle sparse cpu_possible_map
properly.
Please note that on x86, cpu_possible_map() doesn't contain holes and
thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause
any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
