Workaround for imx5x M4IF burst len errata when armv7 neon enabled, use
pgprot_writecombine instead of pgprot_noncached, to avoid burst len > 8.
Signed-off-by: Sammy He <r62914@freescale.com>
HW flow control should be enable/disable by userspace.
It can be set by tty option: options.c_cflag of CRTSCTS
bit.
This bug is found by testing UART BT AR3001 chip,
this chip will wake up the chip by set RTS to high,
it needs frist disable HW flow control, set RTS,
then disable HW flow control.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
If VPU doesn't use IRAM, there will be a kernel dump when
we enter VPU driver probe function.
This issue is caused by allocating IRAM with zero buffer
size.
Signed-off-by: Liu Ying <b17645@freescale.com>
disable dp-dc in the display flow end irq handler, otherwise,
ipu may get NFB4EOF error for next fb enabling under big resolution(like 1080p).
Signed-off-by: Jason Chen <b02280@freescale.com>
This patch adds support for Spansion S25FL016K and S25FL064K SPI flash.
It has been tested with physical devices. Note that both parts exhibit
a Winbond manufacturer ID so they might also be added to that section.
Signed-off-by: Gernot Hoyler <Gernot.Hoyler@spansion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
"plat_id" is always non-NULL here. There is a zero element on the end
of the m25p_ids[] array and if we hit the end of the loop then plat_id
points to that.
This would lead to a NULL pointer dereference later on in the function.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().
Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.
Suggested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since commit 18c6182bae0acca220ed6611f741034d563cd19f ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.
This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.
This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.
[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975
Reported-by: Mingquan Pan
Reported-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
CAT25 chips (as manufactured by On Semiconductor, previously Catalyst
Semiconductor) are similar to the original M25Px0 chips, except:
- Address width can vary (1-2 bytes, in contrast to 3 bytes in M25P
chips). So, implement convenient m25p_addr2cmd() and m25p_cmdsz()
calls, and place address width information into flash_info struct;
- Page size can vary, therefore we shouldn't hardcode it, so get rid
of FLASH_PAGESIZE definition, and place the page size information
into flash_info struct;
- CAT25 EEPROMs don't need to be erased, so add NO_ERASE flag, and
propagate it to the mtd subsystem.
[dwmw2: Fix up for conflicts with DMA safety patch]
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Previosly the driver always tried JEDEC probing, assuming that non-JEDEC
chips will return '0'. But truly non-JEDEC chips (like CAT25) won't do
that, their behaviour on RDID command is undefined, so the driver should
not call jedec_probe() for these chips.
Also, be less strict on error conditions, don't fail to probe if JEDEC
found a chip that is different from what platform code told, instead
just print some warnings and use an information obtained via JEDEC. In
that case we should not trust partitions any longer, but they might be
still useful (i.e. they could protect some parts of the chip).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the m25p80 driver so that now it uses .id_table
for device matching, making it properly detect devices on OpenFirmware
platforms (prior to this patch the driver misdetected non-JEDEC chips,
seeing all chips as "m25p80").
Also, now jedec_probe() only does jedec probing, nothing else. If it
is not able to detect a chip, NULL is returned and the driver fall
backs to the information specified by the platform (platform_data, or
exact ID).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver already uses __devexit_p() in the structure, but looks like
actual __dev{init,exit} markings were forgotten.
The spidev_spi driver also needs renaming to include a "_driver" suffix to
avoid section mismatch warnings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support two new half-duplex SPI implementation restrictions, for links
that talk to TX-only or RX-only devices. (Existing half-duplex flavors
support both transfer directions, just not at the same time.)
Move spi_async() into the spi.c core, and stop inlining it. Then make
that function perform error checks and reject messages that demand more
than the underlying controller can support.
Based on a patch from Marek Szyprowski which did this only for the
bitbanged GPIO driver.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes convention of passing a static string as a
parameter to another static string. The convention is intended to
reduce text usage by sharing the common bits of the string, but the
implementation is inherently fragile (a change to one format string
but not the other will nullify any possible advantage), it isn't
necessarily a net win depending on what this compiler does, and it
it reduces code readability.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[grant.likely@secretlab.ca: removed dev_dbg->dev_err hunk]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently spi_register_board_info() has to be called before its related
spi_master be registered, otherwise these board info will be just ignored.
This patch will remove this order limit, it adds a global spi master list
like the existing global board info listr. Whenever a board info or a
spi_master is registered, the spi master list or board info list
will be scanned, and a new spi device will be created if there is a
master-board info match.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
introduced by 49dce689 ("spi doesn't need class_device") and bad-fixed
by 350d0076 ("spi: fix double-free on spi_unregister_master"),
spi_unregister_master would previously device_unregister all of the spi
master's siblings (instead of its children). hilarity ensues.
fix it to unregister children.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With this patch spi drivers can use standard spi_driver.id_table and
MODULE_DEVICE_TABLE() mechanisms to bind against the devices. Just like
we do with I2C drivers.
This is useful when a single driver supports several variants of devices
but it is not possible to detect them in run-time (like non-JEDEC chips
probing in drivers/mtd/devices/m25p80.c), and when platform_data usage is
overkill.
This patch also makes life a lot easier on OpenFirmware platforms, since
with OF we extensively use proper device IDs in modaliases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In success case the function bus_find_device_by_name calls
get_device. In our context put_device should be called to
decrease the device count usage.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The memory for dev variable is allocated as a part of
spi_device structure memory which the dev belongs to.
Thus when the memory is released the right pointer is used.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is just a cleanup, it doesn't fix any bugs.
These functions all check retlen inconsistently and it generates a
warning in Smatch (http://smatch.sf.net). If retlen were ever NULL it
would cause an oops and the code has been this way since 2006 so someone
would have complained. Also I looked at other places that implemented
the mtd read and write functions and they dereference retlen without
checking.
I removed the checks.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
spi_write() requires the buffer to be DMA-safe, kmalloc()
it seperately to ensure this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SST SPI flashes is like Atmel SPI flashes in that the software
protection bits are set by default at power up, so clear them at init
time.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SST SPI flashes are a bit non-standard in that they can be programmed
one byte at a time (including address!), or they can be written two bytes
at a time with auto address incrementing (AAI). The latter form is
obviously much better for performance, so let's use it when possible.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
