If there is no usb devices connectted or all connectted usb
devices are in suspend state, usb host can suspend its whole bus,
then put the PHY into low power mode and close all usb clocks.
(The patch is splitted 2 patches, this is common code part.)
Signed-off-by: Li Jun <r65092@freescale.com>
the USBPHY of STMP3xxx SoC has bug. The usb port power
is never enabled during standard ehci reset procedure if the
external device once passed plug/unplug procedure. This work-
around resets and reinitiates USBPHY before the ehci port reset
sequence started.
Signed-off-by: Rob Herring <r.herring@freescale.com>
This patch fix OTG pin-detect failure issue.
via sysfs set power/wakeup, i.MX51 can:
Put usb phy into low power mode when system enters stop or
standby mode; Enable usb device remote wakeup system by Vbus
and usb host remote wakeup system by device connection or
disconnection.
Signed-off-by: Li Jun <r65092@freescale.com>
commit 7152b592593b9d48b33f8997b1dfd6df9143f7ec upstream.
This patch (as1352) fixes a bug in the way isochronous input data is
returned to userspace for usbfs transfers. The entire buffer must be
copied, not just the first actual_length bytes, because the individual
packets will be discontiguous if any of them are short.
Reported-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d4a4683ca054ed9917dfc9e3ff0f7ecf74ad90d6 upstream
We need to only copy the data received by the device to userspace, not
the whole kernel buffer, which can contain "stale" data.
Thanks to Marcus Meissner for pointing this out and testing the fix.
Reported-by: Marcus Meissner <meissner@suse.de>
Tested-by: Marcus Meissner <meissner@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jeff Mahoney <jeffm@suse.com>
commit ddeee0b2eec2a51b0712b04de4b39e7bec892a53 upstream
USB: usbfs: properly clean up the as structure on error paths
I notice that the processcompl_compat() function seems to be leaking the
'struct async *as' in the error paths.
I think that the calling convention is fundamentally buggered. The
caller is the one that did the "reap_as()" to get the as thing, the
caller should be the one to free it too.
Freeing it in the caller also means that it very clearly always gets
freed, and avoids the need for any "free in the error case too".
From: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Marcus Meissner <meissner@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jeff Mahoney <jeffm@suse.com>
commit acbe2febe71abb2360b008e9ab3ee5c44169f78c upstream.
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b132b04e193908a94d95065d0628f8fb0159cc55 upstream.
These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: Kurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 49d0f078f494b9d81e820a13dd8093a9bfb0b6b1 upstream.
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c2d284ee04ab6f6718de2ddcf1b43160e046c41d upstream.
USB drivers that create character devices call usb_register_dev in their
probe function. This associates the usb_interface device with that minor
number and creates the character device and announces it to the world.
However, the driver's probe function is called before the new
usb_interface is added to the driver's klist_devices.
This is a problem because userspace will respond to the character device
creation announcement by opening the character device. The driver's open
function will the call usb_find_interface to find the usb_interface
associated with that minor number. usb_find_interface will walk the
driver's list of devices and find the usb_interface with the matching
minor number.
Because the announcement happens before the usb_interface is added to the
driver's klist_devices, a race condition exists. A straightforward fix
is to walk the list of devices on usb_bus_type instead since the device
is added to that list before the announcement occurs.
bus_find_device calls get_device to bump the reference count on the found
device. It is arguable that the reference count should be dropped by the
caller of usb_find_interface instead of usb_find_interface, however,
the current users of usb_find_interface do not expect this.
The original version of this patch only matched against minor number
instead of driver and minor number. This version matches against both.
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c2f6595fbdb408d3d6850cfae590c8fa93e27399 upstream.
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6682bb39e111b34290e25c4d275c5bcf8bbccbe1 upstream.
When there's a descriptor after the SuperSpeed endpoint companion
descriptor, the previous code would have skipped over twice the length it
was supposed to. This code fixes crashes seen with UASP devices (which
have a UASP descriptor after the SS endpoint companion descriptor).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1272) changes the error code returned when an open call
for a USB device node fails to locate the corresponding device. The
appropriate error code is -ENODEV, not -ENOENT.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
access_ok() checks must be done on every part of the userspace structure
that is accessed. If access_ok() on one part of the struct succeeded, it
does not imply it will succeed on other parts of the struct. (Does
depend on the architecture implementation of access_ok()).
This changes the __get_user() users to first check access_ok() on the
data structure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.
However, the previous code would miss the last endpoint in a configuration
with no descriptors after it. Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1262) fixes a bug in usbfs: It refuses to accept
zero-length transfers, and it insists that the buffer pointer be valid
even if there is no data being transferred.
The patch also consolidates a bunch of repetitive access_ok() checks
into a single check, which incidentally fixes the lack of such a check
for Isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b7af0bb ("USB: allow malformed LANGID descriptors") broke support
for devices without string descriptor support.
Reporting string descriptors is optional to USB devices, and a device
lets us know it can't deal with strings by responding to the LANGID
request with a STALL token.
The kernel handled that correctly before b7af0bb came in, but failed
hard if the LANGID was reported but broken. More than that, if a device
was not able to provide string descriptors, the LANGID was retrieved
over and over again at each string read request.
This patch changes the behaviour so that
a) the LANGID is only queried once
b) devices which can't handle string requests are not asked again
c) devices with malformed LANGID values have a sane fallback to 0x0409
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit cc71329b3b, so that
Red Hat machines can boot properly. It seems that the Red Hat initrd
code tries to watch the /proc/bus/usb/devices file to monitor usb
devices showing up. While this task is prone to lots of races and does
not show the true state of the system, they seem to like it.
So for now, don't move this option under the EMBEDDED config option.
Cc: Scott James Remnant <scott@canonical.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added descriptions (for WIRELESS_CONTROLLER and MISC) were taken from
the usb-devices script now included in usbutils.
Also sort the classes in the same order as in include/linux/usb/ch9.h
for easier comparison for future updates.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a memory leak in devio.c::processcompl
If writing to user space fails the packet must be discarded, as it
already has been removed from the queue of completed packets.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1255) updates the interface for calling
usb_hub_clear_tt_buffer(). Even the name of the function is changed!
When an async URB (i.e., Control or Bulk) going through a high-speed
hub to a non-high-speed device is cancelled or fails, the hub's
Transaction Translator buffer may be left busy still trying to
complete the transaction. The buffer has to be cleared; that's what
usb_hub_clear_tt_buffer() does.
It isn't safe to send any more URBs to the same endpoint until the TT
buffer is fully clear. Therefore the HCD needs to be told when the
Clear-TT-Buffer request has finished. This patch adds a callback
method to struct hc_driver for that purpose, and makes the hub driver
invoke the callback at the proper time.
The patch also changes a couple of names; "hub_tt_kevent" and
"tt.kevent" now look rather antiquated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the original patch I created before David Vrabel posted a better
patch (http://marc.info/?l=linux-usb&m=123377477209109&w=2) that does
basically the same thing. This patch will get replaced with his
(modified) patch later.
Allow USB device drivers that use usb_sg_init() and usb_sg_wait() to push
bulk endpoint scatter gather lists down to the host controller drivers.
This allows host controller drivers to more efficiently enqueue these
transfers, and allows the xHCI host controller to better take advantage of
USB 3.0 "bursts" for bulk endpoints.
This patch currently only enables scatter gather lists for bulk endpoints.
Other endpoint types that use the usb_sg_* functions will not have their
scatter gather lists pushed down to the host controller. For periodic
endpoints, we want each scatterlist entry to be a separate transfer.
Eventually, HCDs could parse these scatter-gather lists for periodic
endpoints also. For now, we use the old code and call usb_submit_urb()
for each scatterlist entry.
The caller of usb_sg_init() can request that all bytes in the scatter
gather list be transferred by passing in a length of zero. Handle that
request for a bulk endpoint under xHCI by walking the scatter gather list
and calculating the length. We could let the HCD handle a zero length in
this case, but I'm not sure if the core layers in between will get
confused by this.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally, the USB core had no support for allocating bandwidth when a
particular configuration or alternate setting for an interface was
selected. Instead, the device driver's URB submission would fail if
there was not enough bandwidth for a periodic endpoint. Drivers could
work around this, by using the scatter-gather list API to guarantee
bandwidth.
This patch adds host controller API to allow the USB core to allocate or
deallocate bandwidth for an endpoint. Endpoints are added to or dropped
from a copy of the current schedule by calling add_endpoint() or
drop_endpoint(), and then the schedule is atomically evaluated with a
call to check_bandwidth(). This allows all the endpoints for a new
configuration or alternate setting to be added at the same time that the
endpoints from the old configuration or alt setting are dropped.
Endpoints must be added to the schedule before any URBs are submitted to
them. The HCD must be allowed to reject a new configuration or alt
setting before the control transfer is sent to the device requesting the
change. It may reject the change because there is not enough bandwidth,
not enough internal resources (such as memory on an embedded host
controller), or perhaps even for security reasons in a virtualized
environment.
If the call to check_bandwidth() fails, the USB core must call
reset_bandwidth(). This causes the schedule to be reverted back to the
state it was in just after the last successful check_bandwidth() call.
If the call succeeds, the host controller driver (and hardware) will have
changed its internal state to match the new configuration or alternate
setting. The USB core can then issue a control transfer to the device to
change the configuration or alt setting. This allows the core to test new
configurations or alternate settings before unbinding drivers bound to
interfaces in the old configuration.
WIP:
The USB core must add endpoints from all interfaces in a configuration
to the schedule, because a driver may claim that interface at any time.
A slight optimization might be to add the endpoints to the schedule once
a driver claims that interface. FIXME
This patch does not cover changing alternate settings, but it does
handle a configuration change or de-configuration. FIXME
The code for managing the schedule is currently HCD specific. A generic
scheduling algorithm could be added for host controllers without
built-in scheduling support. For now, if a host controller does not
define the check_bandwidth() function, the call to
usb_hcd_check_bandwidth() will always succeed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is
supposed to follow all SuperSpeed Endpoint descriptors. This descriptor is used
to extend the bus protocol to allow more packets to be sent to an endpoint per
"microframe". The word microframe was removed from the USB 3.0 specification
because the host controller does not send Start Of Frame (SOF) symbols down the
USB 3.0 wires.
The descriptor defines a bMaxBurst field, which indicates the number of packets
of wMaxPacketSize that a SuperSpeed device can send or recieve in a service
interval. All non-control endpoints may set this value as high as 16 packets
(bMaxBurst = 15).
The descriptor also allows isochronous endpoints to further specify that they
can send and receive multiple bursts per service interval. The bmAttributes
allows them to specify a "Mult" of up to 3 (bmAttributes = 2).
Bulk endpoints use bmAttributes to report the number of "Streams" they support.
This was an extension of the endpoint pipe concept to allow multiple mass
storage device commands to be outstanding for one bulk endpoint at a time. This
should allow USB 3.0 mass storage devices to support SCSI command queueing.
Bulk endpoints can say they support up to 2^16 (65,536) streams.
The information in the endpoint companion descriptor must be stored with the
other device, config, interface, and endpoint descriptors because the host
controller needs to access them quickly, and we need to install some default
values if a SuperSpeed device doesn't provide an endpoint companion descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add host controller driver API and a slot_id variable to struct
usb_device. This allows the xHCI host controller driver to ask the
hardware to allocate a slot for the device when a struct usb_device is
allocated. The slot needs to be allocated at that point because the
hardware can run out of internal resources, and we want to know that very
early in the device connection process. Don't call this new API for root
hubs, since they aren't real devices.
Add HCD API to let the host controller choose the device address. This is
especially important for xHCI hardware running in a virtualized
environment. The guests running under the VM don't need to know which
addresses on the bus are taken, because the hardware picks the address for
them. Announce SuperSpeed USB devices after the address has been assigned
by the hardware.
Don't use the new get descriptor/set address scheme with xHCI. Unless
special handling is done in the host controller driver, the xHC can't
issue control transfers before you set the device address. Support for
the older addressing scheme will be added when the xHCI driver supports
the Block Set Address Request (BSR) flag in the Address Device command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a hex route string to each USB device. The route string is used
by the USB 3.0 host controller to send packets through the device tree. USB 3.0
hubs use this string to route packets to the correct port. This is fundamental
bus change from USB 2.0, where all packets were broadcast across the bus.
Devices (including hubs) under a root port receive the route string 0x0. Every
four bits in the route string represent a port on a hub. This length works
because USB 3.0 hubs are limited to 15 ports, and USB 2.0 hubs (with potentially
more ports) will never see packets with a route string. A port number of 0
means the packet is destined for that hub.
For example, a peripheral device might have a route string of 0x00097.
This means the device is connected to port 9 of the hub at depth 1.
The hub at depth 1 is connected to port 7 of a hub at depth 0.
The hub at depth 0 is connected to a root port.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB 3.0 bus specification defines a new connection sequence for USB 3.0
hubs and roothubs. USB 3.0 devices are reset and link trained by the hub
before the port status change notification is sent to the host OS. This means
that an entire tree of devices can be trained in parallel on power up, and the
OS no longer needs to reset USB 3.0 devices. Change the USB core's hub port
init sequence so that it does not reset USB 3.0 devices.
The port status change from the roothub and from the USB 3.0 hub will report
the SuperSpeed connect correctly. This patch currently only handles the
roothub case.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add USB 3.0 root hub descriptors. This is a kludge because I reused the old
USB 2.0 descriptors, instead of using the new USB 3.0 hub descriptors with
endpoint companion descriptors and other descriptors. I did this because I
wasn't ready to add USB 3.0 hub changes to khubd. For now, a USB 3.0 roothub
looks like a USB 2.0 roothub, with a higher speed.
USB 3.0 hubs have no transaction translator (TT).
Make USB core debugging handle super speed ports.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the USB core to handle the new USB 3.0 speed, "SuperSpeed". This
is 5.0 Gbps (wire speed). There are probably more places that check for
speed that I've missed.
SuperSpeed devices have a 512 byte endpoint 0 max packet size. This shows
up as a bMaxPacketSize0 set to 0x09 (see table 9-8 of the USB 3.0 bus
spec).
xHCI spec says that the xHC can handle intervals up to 2^15 microframes. That
might change when real silicon becomes available.
Add FIXME note for SuperSpeed isochronous endpoints. They can transmit up
to 16 packets in one "burst" before they wait for an acknowledgment of the
packets. They can do up to 3 bursts per microframe (determined by the
mult value in the endpoint companion descriptor). The xHCI driver doesn't
have support for isoc yet, so fix this later.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PCI initialization code to take control of the xHCI host controller
away from the BIOS, halt, and reset the host controller. The xHCI spec
says that BIOSes must give up the host controller within 5 seconds.
Add some host controller glue functions to handle hardware initialization
and memory allocation for the host controller. The current xHCI
prototypes use PCI interrupts, but the xHCI spec requires MSI-X
interrupts. Add code to support MSI-X interrupts, but use the PCI
interrupts for now.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently if a laptop is suspended e.g. while docked and then resumed after
undocking it, the following errors get generated because the USB hub in the
docking station and the devices connected to it are no longer available:
pm_op(): usb_dev_resume+0x0/0x10 returns -19
PM: Device 1-2 failed to resume: error -19
pm_op(): usb_dev_resume+0x0/0x10 returns -19
PM: Device 1-2.2 failed to resume: error -19
pm_op(): usb_dev_resume+0x0/0x10 returns -19
PM: Device 1-2.3 failed to resume: error -19
As the removal of USB devices while a system is suspended is a relatively
common use case and in most cases not an error, just return success on
-ENODEV. The user gets informed anyway as the USB subsystem generates
regular disconnect messages for the devices shortly afterwards:
usb 1-2: USB disconnect, address 3
usb 1-2.2: USB disconnect, address 4
usblp0: removed
usb 1-2.3: USB disconnect, address 5
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This replaces dma_sync_single() and dma_sync_sg() with
dma_sync_single_for_cpu() and dma_sync_sg_for_cpu() respectively
because they is an obsolete API; include/linux/dma-mapping.h says:
/* Backwards compat, remove in 2.7.x */
#define dma_sync_single dma_sync_single_for_cpu
#define dma_sync_sg dma_sync_sg_for_cpu
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The endpoint devices look like simple attribute groups now, and no longer
like devices with a specific subsystem. They will also no longer emit uevents.
It also removes the device node requests for endpoint devices, which are not
implemented for now.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1237) changes the way the PCI host controller drivers
avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the memory image. But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.
The pci_resume method is changed to accept a flag indicating whether
the system is resuming from hibernation. When this flag is set, the
drivers will reset the hardware to get rid of any existing state.
Similarly, the pci_suspend method is changed to remove the
pm_message_t argument. It's no longer needed, since no special action
has to be taken when preparing to reinstate the memory image.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1236) converts the USB PCI power management routines
over to the new PM framework.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_host class isn't used for anything anymore (it was used for
debug files, but they have moved to debugfs a few kernel releases ago),
so let's delete it before someone accidentally puts a file in it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1239) updates the kernel's treatment of Unicode. The
character-set conversion routines are well behind the current state of
the Unicode specification: They don't recognize the existence of code
points beyond plane 0 or of surrogate pairs in the UTF-16 encoding.
The old wchar_t 16-bit type is retained because it's still used in
lots of places. This shouldn't cause any new problems; if a
conversion now results in an invalid 16-bit code then before it must
have yielded an undefined code.
Difficult-to-read names like "utf_mbstowcs" are replaced with more
transparent names like "utf8s_to_utf16s" and the ordering of the
parameters is rationalized (buffer lengths come immediate after the
pointers they refer to, and the inputs precede the outputs).
Fortunately the low-level conversion routines are used in only a few
places; the interfaces to the higher-level uni2char and char2uni
methods have been left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the encoding of strings returned by usb_string() from ISO 8859-1
to UTF-8.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
People are very used to the devices file in usbfs. Now that we have
moved usbfs to be an "embedded" option only, the developers miss the
file, they had grown quite attached to it over all of these years. This
patch brings it back and puts it in the usb debugfs directory, so that
the developers don't feel sad anymore.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix sparse warning in drivers/usb/core/hub.c.
The following sparse warning is seen when building on ARM due
do the macro raw_local_irq_save():
warning: symbol 'temp' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix 3 sparse warning in drivers/usb/core/sysfs.c.
warning: symbol '__mptr' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modern systems do not use usbfs; the entries within it are files,
not device nodes, and do not support ACLs which are the default way to
provide access to USB devices to untrusted users.
It is replaced by device-nodes maintained by udev in /dev/bus/usb,
libusb uses this device nodes.
Mark the option as deprecated, and hide entirely for non-embedded builds
(which may not be using udev but require raw USB device access).
Signed-off-by: Scott James Remnant <scott@canonical.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
