I found a bug which can be reproduced by this way:(linux-2.6.26-rc5, x86-64)
(use 2^32, 2^33, ...., 2^63 as shares value)
# mkdir /dev/cpuctl
# mount -t cgroup -o cpu cpuctl /dev/cpuctl
# cd /dev/cpuctl
# mkdir sub
# echo 0x8000000000000000 > sub/cpu.shares
# echo $$ > sub/tasks
oops here! divide by zero.
This is because do_div() expects the 2th parameter to be 32 bits,
but unsigned long is 64 bits in x86_64.
Peter Zijstra pointed it out that the sane thing to do is limit the
shares value to something smaller instead of using an even more
expensive divide.
Also, I found another bug about "the shares value is too large":
pid1 and pid2 are set affinity to cpu#0
pid1 is attached to cg1 and pid2 is attached to cg2
if cg1/cpu.shares = 1024 cg2/cpu.shares = 2000000000
then pid2 got 100% usage of cpu, and pid1 0%
if cg1/cpu.shares = 1024 cg2/cpu.shares = 20000000000
then pid2 got 0% usage of cpu, and pid1 100%
And a weight of a cfs_rq is the sum of weights of which entities
are queued on this cfs_rq, so the shares value should be limited
to a smaller value.
I think that (1UL << 18) is a good limited value:
1) it's not too large, we can create a lot of group before overflow
2) it's several times the weight value for nice=-19 (not too small)
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If GART IOMMU is used on an AMD64 system, the northbridge registers
related to it should be restored during resume so that memory is not
corrupted. Make gart_resume() handle that as appropriate.
Ref. http://lkml.org/lkml/2008/5/25/96 and the following thread.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do not print loglevel before "entries of %ld bytes". Move it to the previous
pr_info.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove obsolete and no longer used PM-related definitions from
include/asm-x86/nmi.h.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
timespec_add_ns is used from the x86-64 vdso, which cannot call out to
other kernel code. Make sure that timespec_add_ns is always inlined
(and only uses always_inlined functions) to make sure there are no
unexpected calls.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
iter_div_u64_rem is used in the x86-64 vdso, which cannot call other
kernel code. For this case, provide the always_inlined version,
__iter_div_u64_rem.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have a few instances of the open-coded iterative div/mod loop, used
when we don't expcet the dividend to be much bigger than the divisor.
Unfortunately modern gcc's have the tendency to strength "reduce" this
into a full mod operation, which isn't necessarily any faster, and
even if it were, doesn't exist if gcc implements it in libgcc.
The workaround is to put a dummy asm statement in the loop to prevent
gcc from performing the transformation.
This patch creates a single implementation of this loop, and uses it
to replace the open-coded versions I know about.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
BTW, what does pat_wc_enabled stand for? Does it mean
"write-combining"?
Currently it is used to globally switch on or off PAT support.
Thus I renamed it to pat_enabled.
I think this increases readability (and hope that I didn't miss
something).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Starting with commit 8d4a430085 (x86:
cleanup PAT cpu validation) the PAT CPU feature flag is not cleared
anymore. Now the error message
"PAT enabled, but CPU feature cleared"
in pat_init() is misleading.
Furthermore the current code does not check for existence of the PAT
CPU feature flag if a CPU is whitelisted in validate_pat_support.
This patch clears pat_wc_enabled if boot CPU has no PAT feature flag
and adapts the paranoia check.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If PAT support is advertised it should just work. No errata known.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clarify the usage of mtrr_lookup() in PAT code, and to make PAT code
resilient to mtrr lookup problems.
Specifically, pat_x_mtrr_type() is restructured to highlight, under what
conditions we look for mtrr hint. pat_x_mtrr_type() uses a default type
when there are any errors in mtrr lookup (still maintaining the pat
consistency). And, reserve_memtype() highlights its usage ot mtrr_lookup
for request type of '-1' and also defaults in a sane way on any mtrr
lookup failure.
pat.c looks at mtrr type of a range to get a hint on what mapping type
to request when user/API: (1) hasn't specified any type (/dev/mem
mapping) and we do not want to take performance hit by always mapping
UC_MINUS. This will be the case for /dev/mem mappings used to map BIOS
area or ACPI region which are WB'able. In this case, as long as MTRR is
not WB, PAT will request UC_MINUS for such mappings.
(2) user/API requests WB mapping while in reality MTRR may have UC or
WC. In this case, PAT can map as WB (without checking MTRR) and still
effective type will be UC or WC. But, a subsequent request to map same
region as UC or WC may fail, as the region will get trackked as WB in
PAT list. Looking at MTRR hint helps us to track based on effective type
rather than what user requested. Again, here mtrr_lookup is only used as
hint and we fallback to WB mapping (as requested by user) as default.
In both cases, after using the mtrr hint, we still go through the
memtype list to make sure there are no inconsistencies among multiple
users.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Rufus & Azrael <rufus-azrael@numericable.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On some boards, the mv643xx_eth MAC isn't connected to a PHY but
directly (via the MII/GMII/RGMII interface) to another MAC-layer
device. This patch allows specifying ->phy_addr = -1 to skip all
PHY-related initialisation and run-time poking in that case.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
During OOM, instead of stopping RX refill when the rx desc ring is
not empty, keep trying to refill the ring as long as it is not full
instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Some SoCs have the TX bandwidth control registers in a slightly
different place. This patch detects that case at run time, and
re-directs accesses to those registers to the proper place at
run time if needed.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Newer hardware has a 16-bit instead of a 14-bit RX coalescing
count field in the SDMA_CONFIG register. This patch adds a run-time
check for which of the two we have, and adjusts further writes to the
rx coal count field accordingly.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Under some conditions, the TXQ ('TX queue being served') bit can clear
before all packets queued for that TX queue have been transmitted.
This patch enables TXend interrupts, and uses those to re-kick TX
queues that claim to be idle but still have queued descriptors from
the interrupt handler.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
As with the multiple RX queue support, allow the platform code to
specify that the hardware we are running on supports multiple TX
queues. This patch only uses the highest-numbered enabled queue
to send packets to for now, this can be extended later to enable
QoS and such.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Allow the platform code to specify that we are running on hardware
that is capable of supporting multiple RX queues. If this option
is used, initialise all of the given RX queues instead of just RX
queue zero.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Add an interface for the hardware's per-port and per-subqueue
TX rate control. In this stage, this is mainly so that we can
disable the bandwidth limits during initialisation of the port.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
General cleanup of the mv643xx_eth driver. Mainly fixes coding
style / indentation issues, get rid of some useless 'volatile's,
kill some more superfluous comments, and such.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Remove the write-only ->[rt]x_int_coal members from struct
mv643xx_eth_private. In the process, tweak the RX/TX interrupt
mitigation code so that it is compiled by default, and set the
default coalescing delays to 0 usec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Split all TX queue related state into 'struct tx_queue', in
preparation for multiple TX queue support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Split all RX queue related state into 'struct rx_queue', in
preparation for multiple RX queue support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The per-port mv643xx_eth_private struct had a private instance
of struct net_device_stats that was never ever written to, only
read (via the ethtool statistics interface). This patch gets
rid of the private instance, and tweaks the ethtool statistics
code in mv643xx_eth to use the statistics in struct net_device
instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Since they are no longer used, kill enum FUNC_RET_STATUS and
struct pkt_info (which were a rather roundabout way of communicating
RX/TX status within the same driver).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
rx_return_buff() is also a remnant of the HAL layering that the
original mv643xx_eth driver used. Moving it into its caller kills
the last reference to FUNC_RET_STATUS/pkt_info.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The port_receive() function is a remnant of the original mv643xx_eth
HAL split. This patch moves port_receive() into its caller, so that
the top and the bottom half of RX processing no longer communicate
via the HAL FUNC_RET_STATUS/pkt_info mechanism abstraction anymore.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Half of the functions in the mv643xx_eth driver are prefixed by
useless and baroque comment blocks on _what_ those functions do (which
is obvious from the code itself) rather than why, and there's no point
in keeping those comments around.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
A bunch of places in the mv643xx_eth driver use the 'mv643xx_'
prefix. Since the mv643xx is a chip that includes more than just
ethernet, this patch makes all those places use either no prefix
(for some internal-use-only functions), or the full 'mv643xx_eth_'
prefix.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The fact that mv643xx_eth is an ethernet driver is pretty obvious,
and having a lot of internal-use-only functions and defines prefixed
with ETH_/ethernet_/eth_ prefixes is rather pointless. So, get rid
of most of those prefixes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Remove the unused rx/tx descriptor field defines, and move the ones
that are actually used to the actual definitions of the rx/tx
descriptor format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
All except one of the port serial status register bit defines are
unused -- kill the unused ones.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The only user of the ETH_MIB_VERY_LONG_NAME_HERE defines is the
eth_update_mib_counters() function. Get rid of the defines by
open-coding the register offsets in the latter.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Get rid of RX_BUF_OFFSET (which is synonymous with ETH_HW_IP_ALIGN).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Replace the nondescriptive names ETH_INT_UNMASK_ALL and
ETH_INT_UNMASK_ALL_EXT by names of the actual fields being masked
and unmasked in the various writes to the interrupt mask registers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
None of the port status register bit defines are ever used in the
mv643xx_eth driver -- nuke them all.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Over half of the port serial control register bit defines are never
used, and the PORT_SERIAL_CONTROL_DEFAULT_VALUE define is never used
either. Keep only those defines that are actually used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Delete the defines for SDMA config register bit values that are
never used in the driver, to tidy up the code some more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The port config extend register is never changed at run time.
Document the meaning of the initial value, and delete the defines
for the individual bits in this register.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>