Update NFC INT wait timeout value to 1s.
1s should be enough for all platforms.
If INT bit not set for 1s timeout value, this
should be high potential of IC issues.
Signed-off-by:Jason Liu <r64343@freescale.com>
Miss clear BYPASS_CPU bit for CLKSEQ. CPU and HClk frequency will low than
24Mhz, so there are not enough bandwidth to support LCD refresh
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Do not disable the eSDHC clk on MX35 3DS board,
since SYSTEM can't boot up after the reset key
is pressed when the SD/MMC boot mode is used.
The root cause is that the ROM code don't ensure
the SD/MMC clk is running when boot system.
Signed-off-by: Richard Zhu <r65037@freescale.com>
if unblank to blank tve fb too quickly, system will hang. It's caused by
unprotected tve register access.
Signed-off-by: Jason Chen <b02280@freescale.com>
1.arrange display port according to choice of different display device
2.for ipu_disp.c: not round pixel clock to even for tvout.
3.cmdline "hdtv" enable 720P, "hdtv=2" enable 720P as primary.
Signed-off-by: Jason Chen <b02280@freescale.com>
add dmfc size control for dynamic change and _setup.
DMFC_NORMAL: segment 0,1 for DC, 4,5 for DP-BG, 6,7 for DP-FG.
DMFC_HIGH_RESOLUTION_DC: segment 0~3 for DC, 4,5 for DP-BG, 6,7 for DP-FG.
DMFC_HIGH_RESOLUTION_DP: segment 0,1 for DC, 2~5 for DP-BG, 6,7 for DP-FG.
DMFC_HIGH_RESOLUTION_ONLY_DP: segment 0~3 for DP-BG, 4~7 for DP-FG.
IPU diplay driver will try to enlarge its related DMFC segment size
when it meet high resolution condition, but if dmfc is already in high
resolution setting, dmfc will not change.That said, first request wins.
For cmdline setting, "dmfc=1" is DMFC_HIGH_RESOLUTION_DC, "dmfc=2"
is DMFC_HIGH_RESOLUTION_DP, "dmfc=3" is
DMFC_HIGH_RESOLUTION_ONLY_DP.
NOTE: DMFC_HIGH_RESOLUTION_ONLY_DP only can be set by cmdline.
Signed-off-by: Jason Chen <b02280@freescale.com>
Setting "video=mxcfb:800x600-16@60" in the exec command makes video not play
correctly, IPU didn't play video when panel blank line where lower then minimum
required by IPU
Signed-off-by: Ran Ferderber r53561@freescale.com
1.GPMI NAND flash scan scheme can overcome the shortcomings
of MTD NAND community code.
2.Put it to the common NAND directory can benifit I.MX NAND
driver besides GPMI NAND driver.
3.Fix the section mismatch build warnings on ALL platforms.
4.Fix the kbuild build errors of I.MX platforms.
Signed-off-by:Jason Liu <r64343@freescale.com>
Disable lcdif controller when suspend or screen blanked.
By doing so, can set CPU freq to 64000Khz (ENGR00119096)
Signed-off-by: Robby Cai <R63905@freescale.com>
pll_set_rate function should only wait for PLL relock if PLL is enabled.
Also add a timeout to the infinte loop.
Signed-off-by: Ranjani Vaidyanathan-RA5478 <Ranjani.Vaidyanathan@freescale.com>
1. Add wait timeout support to void dead loop in NAND driver,
2. Try best to use IRQ mode instead of POLLING mode
Signed-off-by:Jason Liu <r64343@freescale.com>
DVFS-PER needs to make sure that the pixel clock divider is an
even integer.
Added support for pixel clock being sourced from an external clock (PLL3)
Signed-off-by: Ranjani Vaidyanathan-RA5478 <Ranjani.Vaidyanathan@freescale.com>
Write bootstream to kernel by kobs with BCH ECC.
Using the same combined Metadata & Block 0 BCH layout
with ROM code.
Page size 2048B; spare area 64B => ECC8, N=3, B0=512B, M=10B
Page size 4096B; spare area 128B => ECC8, N=7, B0=512B, M=10B
Page size 4096B; spare area 218B => ECC16, N=7, B0=512B, M=10B
Signed-off-by:Jason Liu <r64343@freescale.com>
Update NAND scan scheme to support new nand type. With this patch
Linux NAND driver can support new NAND flash on mx25/mx35 board while
compatible with old NAND on old boards.
Signed-off-by: Jason Liu <r64343@freescale.com>
There is one CSI crop improvement (engr117261) in v4l2 capture.
But the improvement is not suitable for tvin module since the
ACT_FRM_SIZE wouldn't be the same with the SENSOR_SIZE.
Signed-off-by: Miao Yu <r65093@freescale.com>
When add usb gadget driver in OTG mode, cause nobody cared irq,
this pach disable usbintr in udc driver probe.
Signed-off-by: Li Jun <r65092@freescale.com>
iMX23: power supply protection mechanism must be implemented
in order to properly protect the SoC from damage or getting
into a locked up state. Several chip errata exists which (some are
documented and some are not yet documented at the time of this writing).
Signed-off-by: Robert Lee <robert.lee@freescale.com>
1. If there is no usb devices connectted or all connectted usb
devices are in suspend state, usb host can suspend its whole bus,
then put the PHY into low power mode and close all usb clocks.
2. close all usb clocks for usb device low power mode.
(The patch is splitted 2 patches, this is FSL specific driver
part.)
Signed-off-by: Li Jun <r65092@freescale.com>
If there is no usb devices connectted or all connectted usb
devices are in suspend state, usb host can suspend its whole bus,
then put the PHY into low power mode and close all usb clocks.
(The patch is splitted 2 patches, this is common code part.)
Signed-off-by: Li Jun <r65092@freescale.com>
The unexpected messages are printed by the kernel.
The root cause is that the I2C IO func can't be called in the
interrupt context, since the SD/MMC port and CD PIN is logically
walk through the MCU I2C bus.
Solution:Don't call the I2C IO func in the interrupt context in
card detection IRQ handler, move them to work-queue enviroment.
Signed-off-by: Richard Zhu <r65037@freescale.com>
No all regiser use _SCT. stmp3xxx_setl may write to wrong address.
please use __raw_write (value, REG_XXX_SET) to write date to SCT
register. Only REG_XXX_SCT is defined when it exist at hardware.
Signed-off-by: Frank.Li <Frank.Li@freescale.com>
The ASRC cann't work when the SPDIF RX is employed to drive the input
part of the ASRC.
The root cause is miswritting "reg |= 7 << AICPA;" as "reg | 7 <<
AICPA;".
Signed-off-by: William Lai <b04597@freescale.com>
Suspend then resume, kernel will print one warning message.
This is due to mtd suspend/resume framework change on 2.6.31 kernel.
Please refer to the follwing commit for detailed information
commit 15bce40cb3
[MTD] Restore suspend/resume support for mtd devices
Signed-off-by: Jason Liu <r64343@freescale.com>
FEC driver is stopped in suspend state. So FEC driver should restart
instead of initialization in resume state
Signed-off-by: Lily Zhang <r58066@freescale.com>
Support DP gamma by setting piecewise linear approximation,
application need set coefficient const[k] and slope[k]. The algorithm to
calculate these coefficient pls refer to unit test.
Signed-off-by: Jason Chen <b02280@freescale.com>
After switch DP(2 layer) from lcd to tvout, fb1 use RGBP format, the
output of fb1's color was not exactly correct.
Signed-off-by: Jason Chen <b02280@freescale.com>
