There is nothing special about having the init code separate from
the common code, so combine the two.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The common oprofile code assumes the name "PMU" (from Intel's
performance management unit). This is misleading when we
start adding oprofile support for other machine types which
don't use the same terminology. Call it op_arm_* instead of
pmu_*.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The oprofile suspend/resume was missing locking. If we failed
to start oprofile on resume, we still reported that it was
enabled. Instead, disable oprofile on error.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make ARM independent of the way bootmem operates internally. We
now map each node as we initialise it, and place the bootmem bitmap
inside each node, rather than all in the first node.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warnings in arch/arm/kernel/module.c,
arch/arm/mm/consistent.c, drivers/pcmcia/sa1111_generic.c,
and platform support files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The merged version follows the ppc64 version pretty closely mostly,
and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version.
The main difference for ppc64 is that the 'p' command to call
show_state (which was always pretty dodgy) has been replaced by
the ppc32 'p' command, which calls a given procedure (so in fact
the old 'p' command behaviour can be achieved with 'p $show_state').
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sc instruction emulation can't be done the same way on 32-bit
as 64-bit yet, but this should work OK.
Signed-off-by: Paul Mackerras <paulus@samba.org>
EBSA110 only requires hardware.h to be included for a couple of
files. Move the include there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves the XICS interrupt controller code into the
platforms/pseries directory, since it only appears on pSeries
machines. If it ever appears on some other machine we can move it to
sysdev, although xics.c itself will need a bunch of changes in that
case to remove pSeries specific assumptions.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows us to also use entry_64.S from the merged tree and reverts
the setup_64.c part of fda262b897.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
We still had an old copy of i8259.h lying around; this gets rid of it
and corrects the callers of i8259_init and i8259_irq.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since I sent the patch to purge bootinfo.h from ARCH=powerpc and
ARCH=ppc64, setup-common.c has come into existence, and another
#include of bootinfo.h slipped in. This patch removes it. It also
removes include/asm-ppc64/bootinfo.h, which somehow survived the
previous patch which was supposed to remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
For the current time idle_6xx only applies to 6xx ppc32 CPUs
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In arch/ia64/kernel/ptrace.c there is a test for a peek or poke of a
register image (in register backing storage).
The test can be unnecessarily long (and occurs while holding the tasklist_lock).
Especially long on a large system with thousands of active tasks.
The ptrace caller (presumably a debugger) specifies the pid of
its target and an address to peek or poke. But the debugger could be
attached to several tasks.
The idea of find_thread_for_addr() is to find whether the target address
is in the RBS for any of those tasks.
Currently it searches the thread-list of the target pid. If that search
does not find a match, and the shared mm-struct's user count indicates
that there are other tasks sharing this address space (a rare occurrence),
a search is made of all the tasks in the system.
Another approach can drastically shorten this procedure.
It depends upon the fact that in order to peek or poke from/to any task,
the debugger must first attach to that task. And when it does, the
attached task is made a child of the debugger (is chained to its children list).
Therefore we can search just the debugger's children list.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
