Add touchscreen calibration support and the BTN_TOUCH.
The calibration algorithm is from Carlos E. Vidales.
and the calibration data is passed to driver by module param.
This driver passes test on ubuntu and android.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
No all regiser use _SCT. stmp3xxx_setl may write to wrong address.
please use __raw_write (value, REG_XXX_SET) to write date to SCT
register. Only REG_XXX_SCT is defined when it exist at hardware.
Signed-off-by: Frank.Li <Frank.Li@freescale.com>
The keypad interrupt registering must be put at the end of probe,
behind the timer init. Otherwise, interrupt will occur during keypad initial.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Since it's not allowed to do synchronous I2C in the HR timer callback
context we have to switch to using the global workqueue. The work is
scheduled every 1ms when polling rather than 5 us.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
commit 1d9f26262aef6d63ff65eba0fd5f1583f342b69b upstream
Properly handle version of the protocol where standard PS/2 packets
from trackpoint are stuffed into middle (byte 3-6) of the standard
ALPS packets when both the touchpad and trackpoint are used together.
The patch is based on work done by Matthew Chapman and additional
research done by David Kubicek and Erik Osterholm:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/296610
Many thanks to David Kubicek for his efforts in researching fine points
of this new version of the protocol, especially interaction between pad
and stick in these models.
Cc: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Sebastian Kapfer <sebastian_kapfer@gmx.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 5f5eeff4c93256ee93435a3bf08cf18c45e9a994 upstream.
Apparently some of Toshiba Protege M300 identify themselves as
"Portable PC" in DMI so we need to add that to the DMI table as
well. We need DMI data so we can automatically lower Synaptics
reporting rate from 80 to 40 pps to avoid over-taxing their
keyboard controllers.
Tested-by: Rod Davison <roddavison@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When KBC is in active multiplexing mode, disabling and re-enabling the
touchpad with the special key leaves the touchpad dead. Since the laptop
does not have any external PS/2 ports disabling MUX mode should be safe.
Reported-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes, when using the touchscreen, it stops working till next restart
and the following message is printed:
ucb1400: unexpected IE_STATUS = 0x0
The following patch retriggers the touchscreen interrupt unconditionally.
This prevents hanging of the touchscreen in case of bogus interrupt
occurence.
Signed-off-by: Pavel Revak <palo@bielyvlk.sk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Palo Revak <palo@bielyvlk.sk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The KEY_MAX change in 2.6.28 changed the values of the JSIOCSBTNMAP and
JSIOCGBTNMAP constants; software compiled with the old values no longer
works with kernels following 2.6.28, because the ioctl switch statement
no longer matches the values given by the software. This patch handles
these ioctls independently of the length of data specified, and applies the
same treatment to JSIOCSAXMAP and JSIOCGAXMAP which currently depend on
ABS_MAX.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove assumption on the shift and size of rows/columns form
matrix_keypad driver.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Prestigio 157, an old no-name clone laptop uses input keys very
similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled
wireless radio frequency kill switch.
This patch adds support for the RF kill switch control and adds manual
identification of the model.
The Prestigio does not expose any recognisable identity via dmidecode
and so requires manual selection at module init using
force=1 keymap=prestigio
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The synaptic touchpad on the Asus G1S is not properly detected when
rebooting machine or on cold boot from time to time. Adding the Asus
G1S to the noloop exception table resolves the issue.
# dmidecode 2.10
SMBIOS 2.4 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: G1S
Version: 1.0
Wake-up Type: Power Switch
SKU Number:
Family:
Signed-off-by: Jory A. Pratt <geekypenguin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 3d5cb60e ("Input: simplify name handling for certain input
handles") introduced a regression for the EVIOCGNAME/JSIOCGNAME
ioctl.
Before this, patch, the platform device's name was given back to
userspace which was good to identify devices. After this patch, the
device is ("event%d", minor) which is not descriptive at all.
This fixes the behaviour by taking dev->name.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reviewed-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables forced releasing of the Fn+Volume hotkeys
on the Fujitsu Siemens Amilo Pi 3525 notebook.
Signed-off-by: Simon Davie <nexx@nexxdesign.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Gets rid of the following warning:
Platform driver 'pcspkr' needs updating - please use dev_pm_ops
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds DMI information to automatically load the correct
layout for the Maxdata Pro 7000X/DX notebook models. Such notebooks
are clones of Fujitsu Amilo V2000, the hook for the v2000 is being
used and I have tested that perfectly works.
The immediate result of integrating this patch is that the five
special buttons will work on these specific notebook models and that
the RF killswitch will not be activated after suspend. This patch
definitively obsoletes the fsam7400 module which I was still needing
to enable wifi and to fix the RF killswitch suspend problem; in the
current 2.6.30 kernel it is necessary to load the wistron_btns module
with options 'force=1 keymap=1557/MS2141', which was not anyway a
complete workaround.
Signed-off-by: Giuseppe Mazzotta <g.mazzotta@iragan.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_mouse - use standard driver registration method
Input: mark serio and i8042 as suspended when hibernating too
Input: add support for generic GPIO-based matrix keypad
Input: arrange keyboards alphabetically
Input: gpio-keys - avoid possibility of sleeping in timer function
Input: gpio-keys - revert 'change timer to workqueue'
Input: dm355evm_keys - fix kconfig symbol names
Input: wacom - add DTF720a support and fix rotation on Intuos3
Input: i8042 - more reset quirks for MSI Wind-clone netbooks
This patch is needed when the gpio's became available only at late
stages, for example, when using i2c gpio expander.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Serio ports are not being restarted any longer because resume operations
after hibernate do nothing, since the device has not been marked as
suspended. This happens because suspend is only considering the SUSPEND
event but not the FREEZE event.
Note that this driver has still to migrate to dev_pm_ops, but this fixes
this particular bug now.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Original patch by Marek Vasut, modified by Eric in:
1. use delayed work to simplify the debouncing
2. combine col_polarity/row_polarity into a single active_low field
3. use a generic bit array based XOR algorithm to detect key
press/release, which should make the column assertion time
shorter and code a bit cleaner
4. remove the ALT_FN handling, which is no way generic, the ALT_FN
key should be treated as no different from other keys, and
translation will be done by user space by commands like 'loadkeys'.
5. explicitly disable row IRQs and flush potential pending work,
and schedule an immediate scan after resuming as suggested
by Uli Luckas
6. incorporate review comments from many others
Patch tested on Littleton/PXA310 (though PXA310 has a dedicate keypad
controller, I have to configure those pins as generic GPIO to use this
driver, works quite well, though), and Sharp Zaurus model SL-C7x0
and SL-C1000.
[dtor@mail.ru: fix error unwinding path, support changing keymap
from userspace]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Reviewed-by: Uli Luckas <u.luckas@road.de>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function may sleep, so it should not be called in a
timer function. Move gpio_get_value calls to workqueue.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 0b346838c5.
This commit breaks GPIO debouncing by replacing the original mod_timer
with schedule_delayed_work in the interrupt handler. The latter does not
kick the timer further on GPIO line changes as it should to perform
debouncing.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When testing Moblin on various netbooks, we've got reports that
many MSI Wind clones need the i8042 reset quirks for the keyboard
and/or touchpad's proper function.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
