In function of gadget unregister the phy will been put to lowpower
mode,however in function of gadget regisger the phy lowpower mode will
not been cleard when OTG pin detect enabled.
Signed-off-by: Huhui <b29976@freescale.com>
(cherry picked from commit 11dc51645fe5a196f53fb30369698b4cb4d1e296)
1. At reset_irq, the status of port reset is unsure, maybe the reset
process(hardware does it) is finished, and the status of port reset
is also cleared by usb controller. So it only needs to compare to USBSTS
at usb irq process.
2. Due to mx35/mx25 phy's bug, it needs to reset phy when re-open
usb clock next time(Begin to use usb next time)
3. mdelay 100 seconds is too long for resume process, as this code
is only added for mx37, add arch macro for this mdelay. This can
minimize the effect for other platforms.
4. Compile is ok for all imx platform, functional tests are finished
for mx35 and mx23.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The probe is called only pdev->name is the same with driver_name,
So the statement for name judgement is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The max packet length bit mask used for isochronous endpoints should
be 0x7FF instead of 0x8FF. 0x8FF will actually clear higher-order bits
in the max packet length field.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
In OTG mode, entering low power mode after udc probe causes
otg controller can not exit from it when switch to host mode.
this patch let gadget class driver handle it.
Signed-off-by: Jun Li <r65092@freescale.com>
Rename stmp_updater to fsl_updater, as the updater will be shared
across all i.MX platforms that needs MFGTool support.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
In order to add IRAM to the USB Gadget driver, there are 2 kconfig
options to enable. One kconfig option was for USB host and the other
was for Gadget. The current SW required both kconfig to be
enable which is confusing. Also need to add iram_alloc function in
the Gadget driver.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Clean-up USB related Kconfigs. Remove the transceiver selections as this
is defined by the chip/board and is selected in platform data.
Use usb device resources defined in devices.c and fix resource sharing.
Use common otg transceiver functions.
Remove unnecessary OTG ifdefs.
Signed-off-by: Rob Herring <r.herring@freescale.com>
There are out of memory when transfer big size file.
There reason is kernel alloc a memory to get data from usb and put to a list,
and wake up uuc to read it. The problem is that read slower than usb transfer
So list become more and more till out of memory
Signed-off-by: Frank Li <Frank.Li@freescale.com>
When add usb gadget driver in OTG mode, cause nobody cared irq,
this pach disable usbintr in udc driver probe.
Signed-off-by: Li Jun <r65092@freescale.com>
1. If there is no usb devices connectted or all connectted usb
devices are in suspend state, usb host can suspend its whole bus,
then put the PHY into low power mode and close all usb clocks.
2. close all usb clocks for usb device low power mode.
(The patch is splitted 2 patches, this is FSL specific driver
part.)
Signed-off-by: Li Jun <r65092@freescale.com>
MX233: Restructure the STMP378xxx USB Host and Gadget device structures
to be similar to MXC structures. Enable fsl_otg_arc driver to work on
MX233 platform. Remove FSL_USB2_DONT_REMAP requirement.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Conflicts:
arch/arm/mach-stmp3xxx/Kconfig
arch/arm/mach-stmp3xxx/Makefile
arch/arm/mach-stmp3xxx/devices.c
arch/arm/mach-stmp3xxx/include/mach/stmp3xxx.h
arch/arm/mach-stmp3xxx/stmp378x_devb.c
USB will enter low power mode if no vbus power supply.
Only finished this feature in Mx37.
1. When enter low power mode, driver will close usb related clocks
as possible as could.
set usb IP to stop.
Set PHY to low power suspend by setting PHCD bit of portsc.
2. This patch doesn't support low power mode in OTG mode yet.
Signed-off-by: Albert Chen <r65187@freescale.com>
This is gadget file storage changes needed for STMP universal updater
tool (manufacturing flashing tool).
Signed-off-by: Frank Li <Frank.Li@freescale.com>
commit c5deb832d7a3f9618b09e6eeaa91a1a845c90c65 upstream.
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix USB gadget audio: select SND_PCM, like many other sound
drivers do, to fix build errors:
drivers/built-in.o: In function `f_audio_playback_work':
audio.c:(.text+0x15a3e7): undefined reference to `snd_pcm_kernel_ioctl'
audio.c:(.text+0x15a471): undefined reference to `snd_pcm_lib_write'
drivers/built-in.o: In function `_snd_pcm_hw_param_set':
audio.c:(.text+0x15aca7): undefined reference to `snd_interval_refine'
drivers/built-in.o: In function `gaudio_setup':
(.init.text+0x12adf): undefined reference to `_snd_pcm_hw_params_any'
drivers/built-in.o: In function `gaudio_setup':
(.init.text+0x12b43): undefined reference to `snd_pcm_kernel_ioctl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reworked Ethernet gadget has an RNDIS interop problem when used
with the CDC subset driver ... e.g. on PXA 2xx and 3xx hardware,
which currently has a hard time talking to MS-Windows hosts.
The issue is that Microsoft requires USB_CLASS_COMM. Fix by tweaking
the CDC subset driver to not switch to USB_CLASS_VENDOR_SPEC if RNDIS
is used in some other device configuration.
[ UPDATED: some "statements" were comma-terminated; fix that. ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Aric Blumer <aric@sdgsystems.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support OID_802_3_MAC_OPTIONS in gen_ndis_query_resp() of rndis.c to
make RNDIS gadget pass 1c_SetMulticast subtest in Microsoft NDISTest6:
http://www.microsoft.com/whdc/DevTools/tools/NDIStest.mspx
The other tests in NDISTest6 are passed.
[ dbrownell@users.sourceforge.net: remove OID_802_3_MAXIMUM_LIST_SIZE
setting ... it was bogus, this code only handles one entry, not 32.
And we don't know what would break if we lied about that... ]
Signed-off-by: Helen Chen <helen.chen@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The audio gadget driver should use a "Linux" device id, instead
of relying on NetChip's vendor id. So provide one out of our reserved
namespace.
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move USB_GADGET_IMX to the right section of Kconfig as this
controller is available only as integrated on i.MX CPU.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The toggle_bias() function was specified differently for avr32 and at91
architectures. Now, new at91 have the same behavior as avr32.
Consequently, we change to a particular chip function definition: only for
at91sam9rl.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Intel Langwell USB Device Controller is a High-Speed USB OTG device
controller in Intel Moorestown platform. It can work in OTG device mode
with Intel Langwell USB OTG transceiver driver as well as device-only
mode. The number of programmable endpoints is different through
controller revision.
NOTE:
This patch is the first version Intel Langwell USB OTG device controller
driver. The bug fixing is on going for some hardware and software
issues. Intel Langwell USB OTG transceiver driver and EHCI driver
patches will be submitted later.
Supported features:
- USB OTG protocol support with Intel Langwell USB OTG transceiver
driver (turn on CONFIG_USB_LANGWELL_OTG)
- Support control, bulk, interrupt and isochronous endpoints
(isochronous not tested)
- PCI D0/D3 power management support
- Link Power Management (LPM) support
Tested gadget drivers:
- g_file_storage
- g_ether
- g_zero
The passed tests:
- g_file_storage: USBCV Chapter 9 tests
- g_file_storage: USBCV MSC tests
- g_file_storage: from/to host files copying
- g_ether: ping, ftp and scp files from/to host
- Hotplug, with and without hubs
Known issues:
- g_ether: failed part of USBCV chap9 tests
- LPM support not fully tested
TODO:
- g_ether: pass all USBCV chap9 tests
- g_zero: pass usbtest tests
- Stress tests on different gadget drivers
- On-chip private SRAM caching support
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Funtions added:
- setup all the USB audio class device descriptors
- handle class specific setup request
- receive data from USB host by ISO transfer
- play audio data by ALSA sound card
- open and setup playback PCM interface
- set default playback PCM parameters
- provide playback functions for USB audio driver
- provide PCM parameters set/get functions
Test on:
- Host: Ubuntu 8.10, kernel 2.6.27
- Gadget: EZKIT-BF548 with ASoC AD1980 codec
Todo:
- add real Mute control code
- add real Volume control code
- maybe find another way to replace dynamic buffer handling
with static buffer allocation
- test on Windows system
- provide control interface to handle mute/volume control
- provide capture interface in the future
- test on BF527, other USB device controler and other audio codec
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver support for the new high-speed/OtG block that is
in the newer line of Samsung SoC devices such as the
S3C64XX series.
This driver does not currntly have DMA support enabled due
to issues with buffer alignment which need to be sorted out.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for i.MX3x (only tested with i.MX31 so far) ARM
SoCs to the fsl_usb2_udc driver. It also moves PHY configuration before
controller reset, because otherwise an ULPI PHY doesn't get a reset and
doesn't function after a reboot. The problem with longer control transfers
is still not fixed. The patch renames the fsl_usb2_udc.c file to
fsl_udc_core.c to preserve the same module name for user-space
backwards compatibility.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug in the RNDIS code.
Due to this bug gether_connect() fails as the port remains un-initialized.
As a result following USB Compliance Tests were failing.
(1)EndpointDescriptorTest_DeviceConfigured
(2)Interface Descriptor Test.
(3)Halt Endpoint Test.
(4)SetConfigurationTest
The fix aligns rndis code with the CDC ECM for xxx_set_alt().
The above listed USB Compliance test passes with this fix.
Tested working fine on SDP with OMAP 3430.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a zero-length packet has been requested and another packet is
written into the fifo, the MX1 tends to send the first byte of the
previous packet instead of the first byte of the current packet.
The CRC is adjusted accordingly so that this packet is _not_
discarded by the host.
Waiting for the ZLPS bit to clear avoids these bad packets.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some usb serial host drivers expect a short packet before they forward
the data to the application. This is caused by them trying to read more
than one packet at a time. So when the gadget sends an exact multiple
of the maximum packet size, it should append a zero-length packet.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the PXA 27x UDC automatically ACK's some control
packets such as SET_INTERFACE, the gadgets may not get a
chance to process the request before another control packet
is received. The Linux gadgets do not expect to receive
setup callbacks out of order. The file storage gadget only
saves the "highest" priority request.
The PXA27x UDC driver must make sure it only sends one up at
a time, allowing the gadget to make changes before
continuing. In theory, the host would be NACK'd while the
gadget processes the change but the UDC has already ACK'd
the request. If another request is sent by the host that is
not automatically ACK'd by the UDC, then the throttling
happens properly to regain sync.
The observed case was the file_storage gadget timing out on
a BulkReset request because the SET_INTERFACE was being
processed by the gadget. Since SET_INTERFACE is higher
priority than BulkReset, the BulkReset was dropped. This
was exacerbated by turning on the debug which delayed the
fsg signal processing thread.
This also fixes the "should never get in
WAIT_ACK_SET_CONF_INTERF state here!!!" warning.
Reported-by: Vernon Sauder <vernoninhand@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 51790b0..1937d8c 100644
Got pxa27x_udc working on the pxa320 Nomad platform. The
problem was that the pxa3xx UDC is not quite compatible with
the pxa27x UDC in how it handles back-to-back control
packets. The pxa27x probably drops them by default, but the
pxa320 does not, and you have to detect it and set the OPC
bit to clear the zero-length packet.
Signed-off-by: Aric Blumer <aric@sdgsystems.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
