remove extern declaration of handle_IPI() in irq_ia64.c.
Instead, declare it in asm-ia64/smp.h.
Later handle_IPI() will be referenced from another file.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Problem: An application violating the architectural rules regarding
operation dependencies and having specific Register Stack Engine (RSE)
state at the time of the violation, may result in an illegal operation
fault and invalid RSE state. Such faults may initiate a cascade of
repeated illegal operation faults within OS interruption handlers.
The specific behavior is OS dependent.
Implication: An application causing an illegal operation fault with
specific RSE state may result in a series of illegal operation faults
and an eventual OS stack overflow condition.
Workaround: OS interruption handlers that switch to kernel backing
store implement a check for invalid RSE state to avoid the series
of illegal operation faults.
The core of the workaround is the RSE_WORKAROUND code sequence
inserted into each invocation of the SAVE_MIN_WITH_COVER and
SAVE_MIN_WITH_COVER_R19 macros. This sequence includes hard-coded
constants that depend on the number of stacked physical registers
being 96. The rest of this patch consists of code to disable this
workaround should this not be the case (with the presumption that
if a future Itanium processor increases the number of registers, it
would also remove the need for this patch).
Move the start of the RBS up to a mod32 boundary to avoid some
corner cases.
The dispatch_illegal_op_fault code outgrew the spot it was
squatting in when built with this patch and CONFIG_VIRT_CPU_ACCOUNTING=y
Move it out to the end of the ivt.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Replace CONFIG_SND_DEBUG_DETECT with CONFIG_SND_DEBUG_VERBOSE to
represent its meaning more better. This config isn't provided only
for the detection but for more verbose debug prints in general.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hook into the device model to make sure that timekeeping's resume handler
is called. This deals with our clocksource's non-monotonicity over the
save/restore. Explicitly call clock_has_changed() to make sure that
all the timers get retriggered properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch implements Xen save/restore and migration.
Saving is triggered via xenbus, which is polled in
drivers/xen/manage.c. When a suspend request comes in, the kernel
prepares itself for saving by:
1 - Freeze all processes. This is primarily to prevent any
partially-completed pagetable updates from confusing the suspend
process. If CONFIG_PREEMPT isn't defined, then this isn't necessary.
2 - Suspend xenbus and other devices
3 - Stop_machine, to make sure all the other vcpus are quiescent. The
Xen tools require the domain to run its save off vcpu0.
4 - Within the stop_machine state, it pins any unpinned pgds (under
construction or destruction), performs canonicalizes various other
pieces of state (mostly converting mfns to pfns), and finally
5 - Suspend the domain
Restore reverses the steps used to save the domain, ending when all
the frozen processes are thawed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add code to:
1. Deal with the console page being canonicalized. During save, the
console's mfn in the start_info structure is canonicalized to a pfn.
In order to deal with that, we always use a copy of the pfn and
indirect off that all the time. However, we fall back to using the
mfn if the pfn hasn't been initialized yet.
2. Restore the console event channel, and rebind it to the existing irq.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add rebind_evtchn_irq(), which will rebind an device driver's existing
irq to a new event channel on restore. Since the new event channel
will be masked and bound to vcpu0, we update the state accordingly and
unmask the irq once everything is set up.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a config option to set the max size of a Xen domain. This is used
to scale the size of the physical-to-machine array; it ends up using
around 1 page/GByte, so there's no reason to be very restrictive.
For a 32-bit guest, the default value of 8GB is probably sufficient;
there's not much point in giving a 32-bit machine much more memory
than that.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We now support the use of memory hotplug, so the physical to machine
page mapping structure must be dynamic. This is implemented as a
two-level radix tree structure, which allows us to efficiently
incrementally allocate memory for the p2m table as new pages are
added.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add xen handles realted definitions for xen memory which ia64/xen needs.
Pointer argumsnts for ia64/xen hypercall are passed in pseudo physical
address (guest physical address) so that it is required to convert
guest kernel virtual address into pseudo physical address.
The xen guest handle represents such arguments.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The pvfb backend indicates dynamic mode support by creating node
feature_resize with a non-zero value in its xenstore directory.
xen-fbfront sends a resize notification event on mode change. Fully
backwards compatible both ways.
Framebuffer size and initial resolution can be controlled through
kernel parameter xen_fbfront.video. The backend enforces a separate
size limit, which it advertises in node videoram in its xenstore
directory.
xen-kbdfront gets the maximum screen resolution from nodes width and
height in the backend's xenstore directory instead of hardcoding it.
Additional goodie: support for larger framebuffers (512M on a 64-bit
system with 4K pages).
Changing the number of bits per pixels dynamically is not supported,
yet.
Ported from
http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/92f7b3144f41http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/bfc040135633
Signed-off-by: Pat Campbell <plc@novell.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Without console= arguments on the kernel command line, the first
console to register becomes enabled and the preferred console (the one
behind /dev/console). This is normally tty (assuming
CONFIG_VT_CONSOLE is enabled, which it commonly is).
This is okay as long tty is a useful console. But unless we have the
PV framebuffer, and it is enabled for this domain, tty0 in domU is
merely a dummy. In that case, we want the preferred console to be the
Xen console hvc0, and we want it without having to fiddle with the
kernel command line. Commit b8c2d3dfbc
did that for us.
Since we now have the PV framebuffer, we want to enable and prefer tty
again, but only when PVFB is enabled. But even then we still want to
enable the Xen console as well.
Problem: when tty registers, we can't yet know whether the PVFB is
enabled. By the time we can know (xenstore is up), the console setup
game is over.
Solution: enable console tty by default, but keep hvc as the preferred
console. Change the preferred console to tty when PVFB probes
successfully, unless we've been given console kernel parameters.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add pte_flags() to extract the flags from a pte. This is a special
case of pte_val() which is only guaranteed to return the pte's flags
correctly; the page number may be corrupted or missing.
The intent is to allow paravirt implementations to return pte flags
without having to do any translation of the page number (most notably,
Xen).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the new sched_op hypercall, mainly because xenner doesn't support
the old one.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen will trap and emulate clts, but its better to use a hypercall.
Also, xenner doesn't handle clts.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a couple of functions which can write directly to the Xen console
for debugging. This output ends up on the host's dom0 console
(assuming it allows the domain to write there).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rather than making _PAGE_* constants signed, and then relying on
sign-extension to make sure that masks derived from them are wide
enough, just explicitly type them pteval_t. This guarantees that they
and any derived values are the right size for the current pte format.
The reliance on sign extension is fragile, and invokes some very
subtle corners of the C type system.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While debugging latencies in the RT kernel, I found that it would be nice
to be able to filter away functions from the trace than just to filter
on functions.
I added a new interface to the debugfs tracing directory called
set_ftrace_notrace
When dynamic frace is enabled, this lets you filter away functions that will
not be recorded in the trace. It is similar to adding 'notrace' to those
functions but by doing it without recompiling the kernel.
Here's how set_ftrace_filter and set_ftrace_notrace interact. Remember, if
set_ftrace_filter is set, it removes all functions from the trace execpt for
those listed in the set_ftrace_filter. set_ftrace_notrace will prevent those
functions from being traced.
If you were to set one function in both set_ftrace_filter and
set_ftrace_notrace and that function was the same, then you would end up
with an empty trace.
the set of functions to trace is:
set_ftrace_filter == empty then
all functions not in set_ftrace_notrace
else
set of the set_ftrace_filter and not in set of set_ftrace_notrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gcc 4.0 fails to allocate %eax for the pattern operand in the rep
store instructions used by memset; force it to do so by declaring a
register variable.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.
As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
vlan: Use bitmask of feature flags instead of seperate feature bits
fmvj18x_cs: add NextCom NC5310 rev B support
xirc2ps_cs: re-initialize the multicast address in do_reset
3C509: rx_bytes should not be increased when alloc_skb failed
NETFRONT: Use __skb_queue_purge()
VIRTIO: Use __skb_queue_purge()
phylib: do EXPORT_SYMBOL on get_phy_id
netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
WAN: protect HDLC proto list while insmod/rmmod
drivers/net/fs_enet: remove null pointer dereference
S2io: Version update for napi and MSI-X patches
S2io: Added napi support when MSIX is enabled.
S2io: Move all the transmit completions to a single msi-x (alarm) vector
drivers/net/ehea - remove unnecessary memset after kzalloc
au1000_eth: remove useless check
Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
cpmac bugfixes and enhancements
e1000e: use resource_size_t, not unsigned long, for phys addrs
net/usb: add support for Apple USB Ethernet Adapter
uli526x: add support for netpoll
...
If a journal checksum error is detected, the ext4 filesystem will call
ext4_error(), and the mount will either continue, become a read-only
mount, or cause a kernel panic based on the superblock flags
indicating the user's preference of what to do in case of filesystem
corruption being detected.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Align i2c_device_id.driver_data to 8 bytes to not fail on crossbuilds.
(Added in d2653e92732bd3911feff6bee5e23dbf959381db.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
global_reg_snapshot shouldn't be visible in our userspace headers.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d167a518 "[PATCH] x86_64: x86_64 version of the smp alternative patch."
has left the LOCK macro in include/asm-x86_64/atomic.h, which is now
include/asm-x86/atomic_64.h. Its scope should be local to the file, other
architectures don't provide it, I couldn't find an in-tree user of it and
allyesconfig, allmodconfig and allnoconfig build fine without it, so this patch
removes it.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The map size counter passed into, and back out of, sanitize_e820_map(),
was an eight bit type (char or u8), as derived from its origins in
legacy BIOS E820 structures. This patch changes that type to an 'int',
to allow this sanitize routine to also be used on larger maps (larger
than the 256 count that fits in a char). The legacy BIOS E820 interface
of course does not change; that remains at 8 bits for this count, holding
up to E820MAX == 128 entries. But the kernel internals can handle more
when those additional memory map entries are passed from the BIOS via
EFI interfaces.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Extend internal boot time memory tables to allow for up to
three entries per node, which may be larger than the 128 E820MAX
entries handled by the legacy BIOS E820 interface. The EFI
interface, if present, is capable of passing memory map
entries for these larger node counts.
This patch requires an earlier patch that rewrote code depending
on these array sizes from using E820MAX explicitly to size loops,
to instead using ARRAY_SIZE() of the applicable array.
Another patch following this one will provide the code to pick
up additional memory entries passed via the EFI interface from
the BIOS and insert them in the following, now enlarged, arrays.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch is motivated by a subsequent patch which will allow for more
memory map entries on EFI supported systems than can be passed via the x86
legacy BIOS E820 interface. The legacy interface is limited to E820MAX ==
128 memory entries, and that "E820MAX" manifest constant was used as the
size for several arrays and loops over those arrays.
The primary change in this patch is to change code loop sizes over those
arrays from using the constant E820MAX, to using the ARRAY_SIZE() macro
evaluated for the array being looped. That way, a subsequent patch can
change the size of some of these arrays, without breaking this code.
This patch also adds a parameter to the sanitize_e820_map() routine,
which had an implicit size for the array passed it of E820MAX entries.
This new parameter explicitly passes the size of said array. Once again,
this will allow a subsequent patch to change that array size for some
calls to sanitize_e820_map() without breaking the code.
As part of enhancing the sanitize_e820_map() interface this way, I further
combined the unnecessarily distinct x86_32 and x86_64 declarations for
this routine into a single, commonly used, declaration.
This patch in itself should make no difference to the resulting kernel
binary.
[ mingo@elte.hu: merged to -tip ]
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The use of #defines with '##' pre-processor concatenation is a useful
way to form several symbol names with a common pattern. But when there
is just a single name obtained from that #define, it's just obfuscation.
Better to just write the plain symbol name, as is.
The following patch is a result of my wasting ten minutes looking through
the kernel to figure out what 'PB_migrate_end' meant, and forgetting what
I came to do, by the time I figured out that the #define PB_range macro
defined it.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove three extern declarations for routines
that don't exist. Fix a typo in a comment.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch:
x86: convert cpu_to_apicid to be a per cpu variable
introduced a dependency of ipi.h on smp.h in x86
builds with an allnoconfig. Including smp.h in ipi.h
fixes the build error:
In file included from arch/x86/kernel/traps_64.c:48:
include/asm/ipi.h: In function 'send_IPI_mask_sequence':
include/asm/ipi.h:114: error: 'per_cpu__x86_cpu_to_apicid' undeclared (first use in this function)
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
