change virtual size to be triple of the screen size as default
to make pan display works at triple buffer mode.
Signed-off-by: Wu Guoxing <b02248@freescale.com>
There are out of memory when transfer big size file.
There reason is kernel alloc a memory to get data from usb and put to a list,
and wake up uuc to read it. The problem is that read slower than usb transfer
So list become more and more till out of memory
Signed-off-by: Frank Li <Frank.Li@freescale.com>
The error message "Removed only %u out of %u pkts" is printed when multiple
to be acked packets are queued.
if (i++ >= pkts_to_be_removed)
break;
This will break out of the loop and increase the counter i when
i==pkts_to_be_removed and the loop ends up with i=pkts_to_be_removed+1.
The following line
if (i != pkts_to_be_removed) {
BT_ERR("Removed only %u out of %u pkts", i, pkts_to_be_removed);
}
will then display the false message.
The counter i must not increase on the same statement.
Signed-off-by: Wending Weng <wweng@rheinmetall.ca>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initialize the default Flexcan device setting, by passing the
predefined parameters through platform_data.
Signed-off-by: William Lai <b04597@freescale.com>
This change makes us get rid of DIx_SYNC_DISP_ERR. The error sometimes
causes the backgound framebuffer reinitialized automatically, even if
we preview captured video on overlay framebuffer.
Signed-off-by: Liu Ying <b17645@freescale.com>
After TV/LCD switch, PXP uses wrong old FB info to set RGBBUF/RGBSIZE.
This patch fixes this problem by notifying PXP to adjust when FB changed.
Signed-off-by: Robby Cai <R63905@freescale.com>
The TZIC base address for MX51 non TO1 is defined as 0xE0003000,
but the according the MX51 TO2 Ref Manual, it should be 0xE0000000.
The reason the system still works with this error is because the TZIC
registers are mirrored at offset 0x3000.
Signed-off-by: Dinh L. Nguyen <Dinh.Nguyen@freescale.com>
blank/unblank fb during v4l2 playback, unblank will cause current buffer
of display channel to be 1. This patch make the sequence of select
display buffer correct.
Signed-off-by: Jason Chen <b02280@freescale.com>
Change the function strcasecmp(buf, "osc") to strncasecmp(buf, "osc",
3), which only compare the first 3bytes.
Signed-off-by: William Lai <b04597@freescale.com>
To use manually buffer select instead of channel link, which resolve fb
blank during v4l2 running issue.
Signed-off-by: Jason Chen <b02280@freescale.com>
UBO and VBO are 22-bit in CPMEM. When processing a high resolution
frame in YUV format, the value of UV-offset may overflow, but the
driver keeps silent.
Signed-off-by: Liu Ying <b17645@freescale.com>
FEC driver of 2.6.31 kernel remove pin iomux config and PHY reset,
which is in fec_gpio_active() needed for i.MX25 and i.MX35.
Signed-off-by: Li Jun <r65092@freescale.com>
Use DP to do CSC for preview on DPFG instead of using IC channel
so that we can get better performance. This change can make us
get rid of IC channel bandwidth limitation when using IC channel
to do upsizing from low resolution to high resolution and CSC.
This change doesn't touch V4L2 overlay for DPBG, because using DP
to do CSC will change the pixel format for DPBG(usually for GUI).
This change doesn't touch V4L2 capture, because users rarely do
upsizing with high multiple in this case.
Signed-off-by: Liu Ying <b17645@freescale.com>
u-boot set wrong standby contorl for regulators,
while kernel doesn't set standby controls which
cuase system can't wakeup from suspend mode.
Signed-off-by: Wallace Wang <r59996@freescale.com>
The UV offset is set wrongly when idmac does cropping.
This patch changes to get the UV offset from user in this case now.
Signed-off-by: Liu Ying <b17645@freescale.com>
Uniform handling NFC INT bit clearance, the INT bit
will be unformed cleared in the wait_op_done function
after any NFC operation.
Signed-off-by:Jason Liu <r64343@freescale.com>
fix the bug that causes the driver to enable the lcd controller twice,
which will request lcd pins twice.
Signed-off-by: Robby Cai <R63905@freescale.com>
Some kernel resource can be accessed in interrupt handler and user
controlled V4L2 ioctrls, so there is a race condition which makes
the kernel malfunction potentially.
Signed-off-by: Liu Ying <b17645@freescale.com>
Update NFC INT wait timeout value to 1s.
1s should be enough for all platforms.
If INT bit not set for 1s timeout value, this
should be high potential of IC issues.
Signed-off-by:Jason Liu <r64343@freescale.com>
Miss clear BYPASS_CPU bit for CLKSEQ. CPU and HClk frequency will low than
24Mhz, so there are not enough bandwidth to support LCD refresh
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Do not disable the eSDHC clk on MX35 3DS board,
since SYSTEM can't boot up after the reset key
is pressed when the SD/MMC boot mode is used.
The root cause is that the ROM code don't ensure
the SD/MMC clk is running when boot system.
Signed-off-by: Richard Zhu <r65037@freescale.com>
